Replacement Kwikee 28 Series Step for Part 902809025

Question

Question:

Is this step LC3747452 a replacement for KwiKee 902809025 Electric Step?

asked by: Phil B

0

Expert Reply:

The correct replacement step for your 28 Series Kwikee step with the part 902809025 is actually listed as part # LC3747453 on our site.

If you are just needing the replacement frame for this step it is part # LC3747457 while the replacement step motor kit is part # LC379608.

expert reply by: Jon G

0

Answer 1

It looks like the previous owner of the trailer had vehicle tires installed since there are very few trailer tire manufacturers that carry a 235/75R15 size. Even though it might work for a while, trailer tires are always better to use for trailer…

view full answer...

Answer 2

Since your Magnetek 940 is rated for 40 Amps I recommend going with the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger #PD9245C rated for 45 Amps instead of the model #PD9260C you mentioned that's rated for 60 Amps.…

view full answer...

Answer 3

You can either unwire the converter from your current power center and install a standalone converter or you can replace the power center with an all-in-one AC/DC distribution panel with a converter. If you want to only replace the converter you can…

view full answer...

Answer 4

The SAE number you provided is merely an identifier that states that the lamp conforms to certain DOT regulations. The Glo-Brite 410 has been discontinued and is no longer available. The closest replacement we offer is the Optronics #MCL48AB which is…

view full answer...

Answer 5

It looks like the Glo Brite Red 410 is a red side marker lamp. It seems like it's a skinny rectangle shape. We have an LED that resembles the Glo Brite Red 410 #MCL82RB. It's LED so it will last a LONG time! Waterproof too! This is the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Kwikee 28 Series Step for Part 902809025

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching