What is Total Weight When Using Axle Placement Formula

Question

Question:

When measuring the weight of the trailer Should it be empty or all the toys on it

asked by: Alex

0

Expert Reply:

The axle placement formula listed below will need to be calculated using the trailer's gross vehicle weight rating (GVWR). The gross vehicle weight rating (GVWR) is the most the trailer can weigh loaded. This will ensure that the trailer is setup to properly handle a full load. There should be an info tag on the trailer (near tongue) that lists the (GVWR) but if not you would need to contact the trailer manufacturer with your VIN.

expert reply by: Conner L

0

click to enlarge

Answer 1

Bargman tail light #30-86-101 is an 86 series so it is not exactly the same as an 84 series. The correct replacement for a Bargman 84 series LED is module #47-84-420.

view full answer...

Answer 2

While we do have some step solutions for you, none of the traditional style steps have the top step level with the mounting brackets when they are pulled out and/or a bracket mounting width of 29" wide (which is much wider than normal). For your…

view full answer...

Answer 3

What you have on your trailer is called a 5 spoke utility hub, like part #8-174-5UC3. They're pretty common on mobile homes so I'm guessing this is where your axle came from. This is also evidenced by your 8-14.5 tires since they're often…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 8

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 9

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

What is Total Weight When Using Axle Placement Formula

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching