Gooseneck Hitch Adapter for Truck with Rails a B&W Patriot Hitch Fit

Question

Question:

Do they make a goose neck hitch for the Patriot rail

asked by: Kirk J

0

Expert Reply:

If you had a fifth wheel rail kit installed in the bed of your truck that the B and W Patriot hitch part # BWRVK3255 fit we have the Curt Spyder adapter part # 16085 will fit the rails and give you a gooseneck hitch ball in the bed of your truck. Reason being that the Patriot hitch is designed to fit the industry standard fifth wheel rails that most hitches out there are designed to fit. This is what the Spyder is also designed to fit too.

expert reply by: Jameson C

0

Mike

4/27/2024

If you add the 16085 to the patriot, what is it now rated for? If you add the 30,000 lb plate C35HR, what is the rating?

Jameson C.

4/29/2024

@Mike Both of the gooseneck adapters part # 16085 and # C35HR would replace the Patriot fifth wheel hitch and fit into the same rails. The capacities would be 25 and 30k respectively as they become the capacity of the rails.

Answer 1

Hey Shawn, the Curt Spyder adapter part #C35HR that you referenced has a 30k towing capacity. That's more than most gooseneck hitches as well as most fifth wheel hitches so I would say it has more capacity than you would end up needing.

view full answer...

Answer 2

There is an Andersen Ultimate 5th Wheel Connection that clamps onto a standard 2-5/16 inch gooseneck ball including B&W as well as other brands. We do not currently offer that hitch but we do have something that is better. Take a look at the…

view full answer...

Answer 3

I do have a solution for you but the Curt X5 adapter #16310 does not work with the factory gooseneck hitch on the 2018 Ford F-350. Instead you can use adapter #RP30156. It is made to fit the factory puck system (instead of the gooseneck hole) and…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

Hi Seth! The B&W Patriot 5th Wheel Trailer Hitch w/ Slider - Dual Jaw - 18,000 lbs #BWRVK3270 will fit any industry standard rails (also referred to as ISR) perfectly, but there are technically a few rails out there that it will not fit. Those…

view full answer...

Answer 6

Hello Oscar, thanks for reaching out. We have exactly what you are looking for. The 30153 you mentioned are universal industry standard 5th wheel base rails. We sell this exact rail set as part #RP30153. This comes with both rails, and all of the…

view full answer...

Answer 7

Hey William, I did some checking and your 2026 Brinkley G3950 does have a Lippert Goose Box style pin box and has a GVWR of 21k so the correct MORryde Goosetech would be the part #MR24MV that you referenced so you were on the right track! How do you…

view full answer...

Answer 8

Hey Randall, thanks for the pin box number from your Jayco Eagle. With that we are able to determine that the correct MORryde Goosetech would be the part #MR97MV that you referenced. How did you like the Orbital pin box?

view full answer...

Answer 9

Hey Mike! Yes, the Curt Custom Fifth Wheel Installation Kit for Ram Truck - Gloss Finish #C16427-104 will fit your 2024 Ram 2500 diesel. Do you already have a 5th wheel hitch picked out?

view full answer...

Answer 10

Hey William, so the 3 inch hitches do use the larger hitch pin diameter but the 2-1/2 inch hitches still use the smaller one. So with a reducer like the part #38735 technically you would use both sizes. If you check out the picture I attached you can…

view full answer...

Answer 11

Yes, Tina, the MORryde GooseTech is a great modern solution for that. Instead of air bags, it uses a rubber shear-spring to absorb shock without needing air pressure checks. It’s essentially maintenance-free and a big upgrade over traditional…

view full answer...

Answer 12

I have a solution for you, but the Curt X5 5th Wheel Rail system #16310 is not compatible with a B&W Patriot Sliding hitch. Since you already have a B&W Turnoverball system in your bed, the only way to use a sliding hitch would be to use a…

view full answer...

Gooseneck Hitch Adapter for Truck with Rails a B&W Patriot Hitch Fit

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching