Gorilla Lift Compatibility with Tall Side Utility Trailer with Ramp
Updated 09/17/2018 | Published 09/15/2018
Products Featured in This Question
Question:
I am currently overhauling a 6x10 utility trailer I built around 20 years ago. the top sides are made from 1inch square tubing and spanned with expanded metal. The sides are 30inch in height and the tailgate is 55inch height. I have read the recommendations for the Gorilla Lift and realize my trailer side are 6inch over recommended height. Will this product still work for my application? Thanks for your help in advance.
asked by: Bryan L
Expert Reply:
The Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable - 300 lbs # GL1 will be right on the edge of working with your trailer dimensions but it will not be a direct fit. You would need to use a different length of cable 3/16 inch diameter to make it work properly and that cable would need to be obtained from a local hardware store. The 58 inches from loop end to loop end of the Replacement Cable with Quick Link for Gorilla Lift Utility Trailer Tailgate Lift # GLC1-Q1 will be too short for your application.
The extra length of cable would make it work, but will also change the lift strength.
Product Page this Question was Asked From
Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable - 300 lbs
- Lift Supports
- Trailer
- Tailgate Assist
- Steel
- Gorilla-Lift
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Replacement Cable with Quick Link for Gorilla Lift Utility Trailer Tailgate Lift
- Search Results: hub
- Search Results: leaf spring
- Shop: Curt Trailer Breakaway Kit with Trickle Charger, LED Tester, and 5 Ah Lead Acid Battery - Side Load
- Video: Review of the Bearing Buddy Bearing Protectors-BB1980A
- Shop: Provider ST225/75R15 Radial Trailer Tire w/ 15" White Vesper Spoke Wheel - 5 on 5 - LRD
- Search Results: buddy bearings
- Search Results: gorilla lift
- Search Results: bearing buddy cap
- Search Results: bearing
- Search Results: trailer bearings races seals caps
- Shop: Replacement Cables for Conventional Ramp Door Spring - 174" Long - Qty 2
- Shop: Dexter Bearing Kit, 14125A/ 25580 Bearings, 10-36 Seal
- Shop: Lift Assist
- Shop: Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2
- Shop: Grease Cap, 2.44" OD Drive In with Plug - Qty 2
- Video: Gorilla-Lift Tailgate GLC1-Q1 Review
- Video: Hands-On with the Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable
- Video: The Low-Down on the Aluminum AM03 Series Gunmetal Gray Machined Trailer Wheel
- Video: Aluminum AM03 Series Black Machined Trailer Wheel Review
- Video: EZ Gate Tailgate Lift Assist for Open Landscape Trailers Spec Review
- Q&A: Is the Replacement Cable with Quick Link for Gorilla Lift Trailer Tailgate Lift Stainless Steel
- Q&A: How To Lower Spring Tension of Gorilla Lift Tailgate Assist
- Q&A: Tailgate Lift Assist For Trailer with Rails 22.5" From Bed to Top of Rail
- Q&A: Does The Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable # GL1 Have 1 or 2 Assists?
- Q&A: Compatibility of Gorilla-Lift Utility Trailer Tailgate Lift Assist with Flat to the Deck Gate
- Q&A: Replacement Roller Assembly Kit Recommendation for Gorilla Lift # GL1
- Q&A: Troubleshooting Gorilla-Lift Ramp Spring Where One Side of Ramp is Higher Than Other