How to Pick Out Bearing and Bearing Buddy for Jet Ski Trailer
Updated 09/04/2018 | Published 09/03/2018
Products Featured in This Question
Question:
Have a single loader jet ski trailer made by easy loader. I need a bearing kit and Buddy bearing. Which would be the correct size?
asked by: Marty
Expert Reply:
I really wish there was a way to determine what bearings a trailer needed without actually pulling the wheel off and checking, but there isn't. The only two solution I have for you would be to remove the hubs and get the numbers that are stamped on the bearing or for you to remove the hubs and use a digital or dial caliper to measure where the bearings and seal ride (see pic).
With that info I can help you figure out what you need. I attached a link down below that shows all of the bearings we offer as well.
In order to pick out the correct bearing buddy you will need know the pilot hole of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into place. Use a screwdriver to pry off the cap.
Clean the grease off and measure the opening with a caliper like the digital caliper # PTW80157.
Product Page this Question was Asked From
Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Search Results: bearing l44649
- Search Results: bearing buddy
- Search Results: trailer bearings races seals caps
- Search Results: trailer tires and wheels
- Search Results: bearing buddy 1980
- Search Results: l44610
- Shop: Lippert Complete Bearing Kit for 2,200-lb Trailer Axles - L44649 Bearings, L44610 Races
- Shop: Replacement Bearing Kit with Bearings L44649, Races L44610, Seal 10-9 - Fits 1.063" Spindles
- Shop: Bearing Buddy Bearing Protectors - Model 2240 - Chrome Plated - Qty 2
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel - Qty 2
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Shop: Gooseneck Hitch
on Trailer Bearings Races Seals Caps
