Size of Bolt that Comes with Timbren Kit part # TWRW22

Question

Question:

how long are the bolts/how much of the bolt is above the plastic circle

asked by: James D

0

Expert Reply:

The bolt size that comes with the Timbren kit part # TWRW22 is M10x60mm x 1.5. Basically just enough of the bolt comes through the assembly and frame to secure it with the nut on the truck frame.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 4

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Ron, congratulations on the new trailer! I have a Jay Feather myself and love it. You're definitely off to a great start with a weight distribution hitch, it will make a world of difference towing that trailer with your F-150. The Weigh Safe…

view full answer...

Answer 8

Hi Doug! If you were just needing a weight distribution system for the sway control, I would have said the Andersen Weight Distribution Hitch w Sway Control - 6" Drop/Rise - 14K GTW, 1.4K TW #AN53VR could be a good option. However, I have tried…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Hey there Layla! There are a few different forms of weight distribution hitches, but the majority of the systems that have sway control use friction bars, which work similar to brake pads on your vehicle. This works really well, but it can sometimes…

view full answer...

Answer 12

Hello again Frank; tongue weight is typically 10-15% of your trailer weight. At 5,400 lbs you could go over the max 800 lb tongue weight of the #FA94-00-0800 but that probably isn't the case here. If you really want to be sure you could always…

view full answer...

Size of Bolt that Comes with Timbren Kit part # TWRW22

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching