Installing EcoHitch Trailer Hitch Receiver on a 2013 Subaru Outback

Question

Question:

I am interested in the EcoHitch Class III Hitch for my 2013 Subaru Outback, which I understand installs behind the rear bumper. The information on your web site indicates the rear bumper needs to be removed and the exhaust lowered for installation. However, the installation video for this part at torkliftcentral.com seems to show only the lowering of the exhaust. Before I order, I just want to confirm whether the hitch attaches behind the rear bumper guard or under the frame. Do you have an installation video on your website that applies to my vehicle? Thanks.

asked by: Nathan R

1

Helpful Expert Reply:

The EcoHitch Hidden Trailer Hitch Receiver # 306-X7162 is a fit for your 2013 Subaru Outback. We recommend removing the bumper fascia because the fascia will require trimming, but Torklift doesn't require it. Their installation details offer two methods of installation, one that requires removing the bumper and one that enlarges the holes instead. The video by the manufacturer shows one of these two installation methods.

expert reply by: Jason S

1

click to enlarge

Answer 1

I'm not exactly sure what you mean by "direct fit" because all three of the Class III trailer hitch receivers we carry for your 2014 Subaru Outback are custom made and designed for your vehicle. The hitch that has the most factory-like…

view full answer...

Answer 2

The information I have says the #306-X7162 has a ground clearance measurement of 10-1/2". The Curt #C13410 has approximately 12" to 12-1/2" of clearance when measured to the bottom of the receiver. I'm not 100% sure how accurate…

view full answer...

Answer 3

There are really two main types of trailer hitches for a 2019 Subaru Outback, visible like the etrailer Trailer Hitch Receiver part #e98847 and hidden like the etrailer Trailer Hitch Receiver part #e42TR. The visible hitch means you can see the cross…

view full answer...

Answer 4

Thanks for the nice words, and on a scale of 1-10, the installation difficulty on your 2019 Subaru Outback is rated a 10 for the etrailer Trailer Hitch Receiver #e42TR. This is somewhat subjective, of course, and we have it as a higher rating…

view full answer...

Answer 5

Hey Sidney, the etrailer hitch part #e42TR fits behind the rear impact bar and does not replace it. How come you are wanting to upgrade to a 2 inch hitch?

view full answer...

Answer 6

We do have the EcoHitch Hidden Trailer Hitch Receiver #306-X7601 which uses more steel to connect the crossbar to the end of the receiver on your 2017 Subaru Outback. This receiver is also made in the USA and comes with a limited lifetime warranty…

view full answer...

Answer 7

The Master Lock hitch and coupler lock set #1481DAT includes a coupler lock (the smaller one) that would fit in a hole on a latch style coupler provided that hole is 1/4 inch in diameter (which is industry standard). With the lock in place whether…

view full answer...

Answer 8

The minimum crossbar spread for the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs #TH898 is 24" - meaning from one point on the front crossbar to the same point on the crossbar has to measure at least 24" for the…

view full answer...

Answer 9

The Hullavator Pro #TH898 will work just fine with Yakima round bars and will not require any additional hardware like what you mentioned. The only step that you will skip in the instructions is installing the special angled end cap (page 5) but my…

view full answer...

Answer 10

I may have a solution for you, but your 53" bars are not going to be sufficient for this task. The Thule Hullavator #TH898 requires 28.5" of usable bar space with 4"-8" outside of the rails/towers, in order to function properly;…

view full answer...

Answer 11

The Retractable Tongue Kit for Malone MicroSport Trailers #MPG494 is designed to replace a damaged tongue on a MicroSportXT #MPG460XT, or to upgrade the tongue on a Malone MicroSport Trailer #MPG460G. Both of these trailers have an overall length of…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Installing EcoHitch Trailer Hitch Receiver on a 2013 Subaru Outback

Continue Researching