Will Bulldog Powered Drive Kit Fit a Fulton 12K Magnum Jack

Question

Question:

Is this Bull Dog Powered Drive kit compatible with a Fulton Magnum Series Heavy Duty 12,000 Lb. Capacity Leg jack. Use is horse trailer with living quarters. Currently manual crank.

asked by: Teri

0

Expert Reply:

Bulldog Powered-Drive Kit # BD1824200100 comes with the parts needed to install and use the kit with your Fulton Magnum 12K jack as long as it was made after 2003. If it was made in 2003 or earlier then there isn't a kit for it.

expert reply by: Michael H

0

Answer 1

The photos you attached did not come through but in order to replace your Fulton 12K Magnum Series HD Jack, I recommend using the Bulldog Square Jack part #BD182701 which has a 12,500 lbs capacity and offers up to 12-1/2" of lift. Unfortunately,…

view full answer...

Answer 2

I have a replacement jack option for you, I reached out to my contact at Fulton and the Fulton Magnum Series 12000lb got discontinued a few years back, and all of the rebuild kits and replacement parts were discontinued with it. The only option is…

view full answer...

Answer 3

MaxxAir vents that have an integrated rain sensor, like the MaxxFan Plus Roof Vent #MA00-04500K, do not allow you to override the sensor. If you were to override it you would be allowing rain to hit the motor which could definitely damage it. The…

view full answer...

Answer 4

Since Equalizer specifically recommends a hitch ball at or less than 2-3/8 inches in length with a 1-1/4 inch diameter shank you would want to use the part #63018 for a 2 inch ball or part #63019 for a 2-5/16 inch hitch ball with the part #EQ37100ET.…

view full answer...

Answer 5

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 6

To access the gears inside of the heavy-duty Bulldog jacks, like part #BD182415, you simply remove the screws that are holding on the plate covering the top of the jack. Once that plate is removed, the gears, pins and handle should be exposed. We…

view full answer...

Answer 7

I attached a picture that details how to disassemble the Bulldog 12,000 lb jacks.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Hayden; that bolt pattern is really uncommon but I believe it can be found on some really old Airstream trailers. There are no modern replacements that will match. The best option is to replace the hub with one that has a common bolt pattern like…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Will Bulldog Powered Drive Kit Fit a Fulton 12K Magnum Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching