Gooseneck Hitch Ball Recommendation for Curt Gooseneck with Taller Height

Question

Question:

I have 2015 ram 3500 with Curt in goose neck ball. Like to have taller ball. I noticed the Reese extended ball. Will this interchange with my Curt system.?

asked by: Phil B

0

Expert Reply:

Since you have a Curt gooseneck hitch the best option we have would be the Curt 4 inch offset double lock ball part # C602 which has a 4 inch offset and sits taller than the standard hitch balls.

expert reply by: Jameson C

0

Answer 1

To add a gooseneck ball and safety chain holders to your Ram factory puck system, you will want the Curt Ball and Safety Chain Loop Kit for Ram Underbed Gooseneck Hitch item #C58CR. This kit works with the factory-installed gooseneck hitches on Dodge…

view full answer...

Answer 2

Yes, the High-Rise Pop-In Ball for Reese Elite Series Underbed Gooseneck Hitch, #RP19315, will work in the factory installed gooseneck hitch on your 2015 Ford F-250 Super Duty. As for the parts being interchangeable, the Reese Elite Series offers the…

view full answer...

Answer 3

What I believe you are looking for is a product like the B&W Extend-A-Goose Gooseneck Coupler #BWTEXA4200. This will fit nearly all gooseneck hitch balls so it should work well for you in that regard as well as it will fit the standard 4 inch…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Gooseneck Hitch Ball Recommendation for Curt Gooseneck with Taller Height

Products Featured in This Question

Continue Researching