Possible Bearing Kit to Fit Trailer With Grease Seal GS-1719

Question

Question:

i removed the bearing on my utility trailor the inner bearing number is LG 63149 THE RACE HAS T R P GS 1719 DL THIS IS A 2003 UTILITY TRAILOR DOUBLE AXEL I AM TRYING TO FIND NEW BEARING KITS TO REPLACE ALL 4 WHEEL BEARINGS CAPS ECT

asked by: Fawn M

0

Expert Reply:

The grease seal you have is the 58846 which is for 3,500 lb axles so most likely for a bearing kit you'd want the # BK2-100 since this comes with the L44649/L68149 Bearings, 10-19 Double Lip Seal.

The bearing number you mentioned doesn't match anything we have so you'll need to verify by measuring the spindles of the trailer. The spindles will need to be 1.06 inch and 1.38 inch where the bearings ride.

expert reply by: Jameson C

0

Answer 1

Based on previous information we have for your UFP HD-1377-10 hub it uses the following components. I do recommend pulling one of your hubs to verify that the replacements listed below match your current parts. Inner Bearing #L68149 (Inner diameter…

view full answer...

Answer 2

I have a replacement for you; our #58846 grease seal is actually a double lip seal like you wanted, and if that is the seal number you're finding on the back of your existing seal, you are able to use that as the replacement. For reference, this…

view full answer...

Answer 3

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 4

Hello Mike, thanks for reaching out. Going from a 255/45ZR/18 tire to a 245/45ZR/18 would not make any noticeable differences in performance. The new tires would not be quite as large in diameter do the deck height would be lowered very slightly.…

view full answer...

Answer 5

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 6

Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Hey Travis, the Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 for a kit that includes the correct bearings and seal. Are you doing yearly maintenance or…

view full answer...

Answer 9

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 10

Hey Greg, There unfortunately there isn't a guide to tell us the bearing and grease seal combination for your hub so you'll have to remove it and check the bearings/seal for their part numbers or use a digital caliper #PTW80157 to measure the…

view full answer...

Answer 11

I believe you meant a TDE 46245, is that correct? If that's the case, you've got a 3500 lb axle which uses a 10 inch hub/rotor with a 5 on 4-1/2 wheel bolt pattern. You'll want to use the Kodiak #KHR10D hub/rotor as a replacement. The hub…

view full answer...

Possible Bearing Kit to Fit Trailer With Grease Seal GS-1719

Product Page this Question was Asked From

Continue Researching