Aluminum Adjustable Ball Mount Recommendation with 2 inch and 1-7/8 inch Hitch Balls

Question

Question:

Im looking for a double ball hitch in aluminum, but I need a 1 7/8inch ball, and a 2inch ball. Do you have that combination on any of your hitches, or can you make one special?

asked by: Scott

0

Expert Reply:

To get an aluminum adjustable ball mount that can have a 1-7/8 inch ball on it you would need to replace the balls of the # FA42-00-2400 with the part # DTBM23 and then you would have a 1-7/8 inch ball and a 2 inch ball.

expert reply by: Jameson C

0

Answer 1

Hello Hans, thanks for reaching out. The Bulletproof ball mounts are only available with 2" and 2=5/16" balls. We do have other options though is you want a ball mount with a 1-7/8" and a 2" ball. I will list a few options for you…

view full answer...

Answer 2

For an aluminum adjustable ball mount that has both a 2 inch and a 1-7/8 inch hitch ball you would want the Rapid Hitch part #AM3411 which has those two ball sizes. I attached a review video for you to check out as well.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Aluminum Adjustable Ball Mount Recommendation with 2 inch and 1-7/8 inch Hitch Balls

Product Page this Question was Asked From

Continue Researching