Replacement Tail Lights Needed for Monarch # 5237 Tail Lights
Updated 12/10/2024 | Published 03/19/2018
Question:
I have Monarch #5237 tail light and would like to covert to led. My problem is that they fit in a pocket with space for 2 1/2 inch tall by 2 7/8 deep. Do you have anything that would fit my needs?
asked by: Jim T
Expert Reply:
The closest LED option that we have to your Monarch # 5237 tail lights is the Optronics LED Trailer Light Kit # TLL160RK. These measure 2-7/8" tall, 8-1/16" wide, and 2-13/16" deep.
The kit will fit as far as depth goes, but they are slightly higher than what you currently have.
I have attached a picture showing the dimensions as well as a review video for you to check out.
Product Page this Question was Asked From
Optronics LED Combination Trailer Tail Lights - Submersible - 40 Diodes - Driver and Passenger Side
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- License Plate
- Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 8L x 3W Inch
- Red
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Optronics LED Combination Trailer Tail Lights - Submersible - 40 Diodes - Driver and Passenger Side
- Search Results: 20245
- Video: A Closer Look at the TecNiq LED Trailer Tail Light
- Search Results: trailer tires and wheels
- Shop: Hydraulic Trailer Brake - Uni-Servo - Free Backing - 10" - Right Hand - 3,500 lbs
- Shop: Americana Baby Moon Trailer Wheel Center Cap - Chrome-Plated Steel - Qty 1
- Search Results: 20041
- Shop: Optronics LED Trailer Light - Brake, Tail, Turn - Submersible - Oval - Red
- Search Results: h20043
- Search Results: 50~67~005
- Search Results: hopkins breakaway
- Search Results: hopkins breakaway switch
- Shop: Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side
- Shop: LED Identification Light Bar for Trailers over 80" Wide - Submersible - 9 Diodes - Red Lens
- Shop: LED Tail Light for Trailers Over 80" Wide - 8 Function - Submersible - 22 Diodes - Driver Side
- Shop: Brake Controller
- Q&A: Trailer Wiring Using Wishbone or Y-Harness 4-Way Trailer Connector
- Article: Trailer Wiring Diagrams
- Q&A: 13" Powder Coated Trailer Wheel That Accepts A Baby Moon Hub Cap
- Video: All You Need to Know About the LED Combination Trailer Tail Light
- Video: Breaking Down the LED Combination Trailer Tail Light
- Q&A: Looking For Tail Light To Replace Monarch 5236 Lights
- Q&A: Trailer Turn Signals Both Blink when Just Left Turn Signal is Activated
- Q&A: What Size Wire For Electric Trailer Brakes When Re-Wiring Trailer
- Q&A: 14 inch Trailer Wheel Recommendation that Can Have Baby Moon Cover Installed
- Video: Ultimate Overview of the Optronics LED Combination Trailer Tail Lights
- Q&A: Triton Utility Trailer LED Light Replacement
- Article: Ram Trailer Tow Prep Package
- Video: Installation: B and W Companion Sliding 5th Wheel Hitch w/ Turnoverball for Ram on a 2021 Ram 2500
- Video: A Closer Look at the Quick Splices
Jeffk
12/10/2024
Same problem, tailer companies used steel tubing 2&1/2" high. Obviously, you can't make that steel larger and companies make the lights to large to fit. 3/8" is a lot try to fit. I tried to use a belt sander but it's a lot to take off.?? What was a good mount, is now frustration.