What Is the Length Of Threaded Portion of Redline Replacement U-Bolt # 176500

Question

Question:

On Redline Trailer Suspension u-bolt - 176500 what is the length of the threads?

asked by: R S

0

Expert Reply:

I walked out to our warehouse to measure the threaded portion of the Redline Replacement U-Bolt # 176500. The threaded portion of the U-Bolt measured 3 inches.

I have attached a picture that I added this measurement to, illustrating this measurement.

expert reply by: Reno H

0

click to enlarge

Answer 1

Hello Chris, The grease that is used to pre-grease our hubs is a lithium based grease. They come pre-greased from AxleTek. With that being said, if you are looking to add more grease it doesn't need to be brand specific. What we use here in our…

view full answer...

Answer 2

The U-bolts that come with Lippert Components Bolt-On Shock Kit w/ Heavy Duty Gas Shocks part #LC281281 measured a length of right at 7-1/8 inches and the thread measures 2 inches in length. I have attached a diagram for your reference. I recommend…

view full answer...

Answer 3

Hey Michael, thanks for reaching out! The best way to level out your 2024 Ram 2500 while towing your 5th wheel is to use an air bag kit and for that I recommend the Firestone Ride-Rite Air Helper Springs #F2598. The feel of your ride while loaded…

view full answer...

Answer 4

The only difference between the Dexter 7K hubs and hub and drum assemblies that have either 1/2 inch studs or 9/16 inch studs are the studs themselves. Otherwise they are exactly the same. You can use calipers such as #PTW80157 to measure the…

view full answer...

Answer 5

The Air Lift WirelessONE compressor system #AL25980 will automatically adjust the air pressure if the air pressure in your air springs falls below the minimum safe level of 5 psi. The system's low-pressure sensor detects the decrease in air…

view full answer...

Answer 6

The grease that comes in our pre-greased hubs like the #AKHD-550-35-K is a lithium based grease. For bearing grease I recommend either the LubriMatic Multi-purpose lithium grease #L11315 or the LubriMatic LMX Industrial Strength Grease #L11390. This…

view full answer...

Answer 7

The Redline Replacement U-Bolt, part #176500, has 9/16 inch x 18 UNF threads per inch, which is a fine thread. It is a Grade 5 round U-bolt.

view full answer...

Answer 8

It sounds like you have a 3" diameter trailer axle and if that is the case then the best option we have is the -Replacement U-Bolt w/Nuts part #176500 which measures 7-1/4" long x 9/16" diameter. I am not aware of any 3/4"…

view full answer...

Answer 9

Generally the 7,000 lb Lippert axles are going to use standard sizing. With the brakes being the 12" x 2" with a 5 bolt backing plate, and the hubs being an 8 lug, and using the standard 1.25" Outer and 1.75" Inner bearing. While…

view full answer...

Answer 10

I was unable to identify your exact axle but I found Trailer Hub and Drum Assembly #AKHD-865-7-2-EZ-K to work if you have EZ Lube axles. If you do not have EZ Lube axles use Trailer Hub and Drum Assembly #AKHD-865-7-2-K. Both of these kits will come…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

What Is the Length Of Threaded Portion of Redline Replacement U-Bolt # 176500

Product Page this Question was Asked From

Continue Researching