Hub/Rotor K2HR958QD11 Compatibility with Spindles on 1970s Axle
Updated 01/23/2018 | Published 01/22/2018
Products Featured in This Question
Question:
Im trying to find out if I can put those disk for a duly its an older axle from the 70s the dimensions of the shaft are 3 1/2 inches from the backing plate which I can go ahead and remove and adjust I do know how to weld and modify items like that it is 8 inches and three quarters measuring in the center of the Springs is 51 inches and 1/8 the length of the axle which I dont know if this matters is 77 1/4 the inside linked overall outside link is 82 inches axle spacing from axle to rear axle is 44 inches my concern is finding out if you do have the bearings that will fit this shaft and we can put those rotors on
asked by: Mike B
Expert Reply:
To find out if a hub/rotor kit like Kodiak # K2HR958QD11 will fit on an existing axle/spindle setup you need to know what bearings are required for the spindle. This 10K disc brake kit uses inner bearing # 28580 and outer bearing # 25580 and these bearings fit on a number 99 spindle. An article on popular bearings is linked.
To know what bearings fit your spindles you will need to either have the original bearing numbers or measure the spindles very precisely using a digital caliper. Please refer to the linked diagram that shows you where to measure the spindles with a caliper like # PTW80157.
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 11" Rotor - 8 on 6-1/2 - Dacromet - Leaf Spring - 10K Rockwell
- Trailer Brakes
- Disc Brakes
- Marine Grade
- 8 on 6-1/2 Inch
- Hub and Rotor
- 5/8 Inch Studs
- 9000 lbs Axle
- 10000 lbs Axle
- 16-1/2 Inch Wheel
- 17-1/2 Inch Wheel
- Kodiak
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Dexter E-Z Flex Equalizer Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs
- Search Results: tarp
- Search Results: roll tarp
- Search Results: k71~652~00
- Search Results: brake drum
- Search Results: bearing 28580 trailer bearings races seals caps
- Q&A: Hub And Drum Replacement for 90865 Rockwell Hub and Drum
- Shop: Trailer Hitch
- Shop: Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs
- Shop: Dexter Trailer Idler Hub Assembly for 9,000-lb to 10,000-lb Axles - 8 on 6-1/2 - Oil Bath
- Shop: Dexter Trailer Hub and Drum Assembly for Heavy-Duty 10K Axles - 8 on 6-1/2 - Oil Bath
- Shop: Replacement Trailer Hub Bearing - 28580
- Shop: Dexter Trailer Hub Drum Assembly - 9K to 10K - 8 on 6.5 - Oil Bath - Non-ABS Drum - After July 2009
- Shop: Dexter Trailer Hub and Drum Assembly for 9K to 10K Axles - 8 on 6-1/2 - Oil Bath - Before July 2009
- Search Results: 205/75r15
- Search Results: k71~654~00
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Replacement Hub Solution for Dexter 8-155
- Q&A: Complete Disc Brake Conversion Kit For A Tandem 10,000 Pound Dexter Axle
- Q&A: Replacement For TDE LP75 Disc Brake Actuator
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Q&A: Outside Dimensions Of The Replacement Left/Curb Side Leg for etrailer and Ram Hydraulic Jack e63VV
- Q&A: Torque Needed For Wheel on Kodiak Disc Brake Kit K2HR526D
- Q&A: Torque Specification for Lugs Nuts on 5/8-Inch Stud on Dexter Hub
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Ram Trailer Tow Prep Package