Replacement Motor for Lippert Components Ground Control 3.0 Auto Leveling System

Question

Question:

Thanks for your quick reply. The problem I'm having is with my Gen 3 Lippert self leveling system. Today I swapped the motor in question with another that was working well. I found that the same problem was still there so I am working down the line. The circuit board is Lippart part number 304136 Can you price that for me and I would also appreciate a price for the two cables that run less than 5' from the circuit board to the front motor. Each motor has two cables, one as a controller and the other for power. Clear as mud? Not sure yet which is bad. Thanks

asked by: Bruce K

1

Helpful Expert Reply:

The Lippert Ground Control 3.0 auto Leveling System does have replacement motors available. I recommend the Replacement Hall Effect Motor for Lippert Components Ground Control 3.0 Leveling System # LC343758 which is a confirmed fit for your 2014 Open Range 386FLR trailer. This motor will simply connect to your current system and will work perfectly as it measures rpms instead of amps for proper auto leveling.

expert reply by: Jason S

1

Bruce K.

12/12/2017

Thanks for your quick reply. The problem I'm having is with my Gen 3 Lippert self leveling system. Today I swapped the motor in question with another that was working well. I found that the same problem was still there so I am working down the line. The circuit board is Lippart part number 304136 Can you price that for me and I would also appreciate a price for the two cables that run less than 5' from the circuit board to the front motor. Each motor has two cables, one as a controller and the other for power. Clear as mud? Not sure yet which is bad. Thanks

Jason S.

12/12/2017

Because you had the same issue when you swapped motors, the issue is either in the wiring or the control module. You can use a circuit tester like # PTW2993 to test your wires probing every few feet for function. If the wires are not the issue, then the Control Module you are looking for is the Replacement Control Module for Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC304136. Before replacing, check those fuses using that circuit tester or swapping with one that you know works properly as sometimes they can look okay and still not function correctly. The two wires from the controller to each motor actually can both be power. To move the motor clockwise one wire will be power and the other neutral. Then to move counterclockwise they will switch with the other being power. Sometimes the quick connect connects are the issue, so you will want to test them both unplugged and plugged in to see if that is the issue.

Answer 1

Hi Kohlton; the Coleman-Mach Signature Mach 15 #CM89RR is a new R32 AC unit. Everything switched to R32 refrigerant last year due to new EPA regulations. Since these operate at different pressures and temperatures they aren't backwards…

view full answer...

Answer 2

Based on the model numbers you provided, it appears that you currently have the Lippert 3.0 Electric Leveling System installed on your trailer. For a replacement motor, you will just need the Lippert Replacement Motor #LC343758. This will serve as an…

view full answer...

Answer 3

I spoke with Lippert and they let me know that the correct replacement motor for your unit is the Replacement Hall Effect Motor for Lippert Components Ground Control 3.0 Leveling System #LC343758. Attached is a product overview video for you to check…

view full answer...

Answer 4

The standard checklist when troubleshooting a error with the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC358590 is as follows: 1. Check harness connections at controller and at jack. 2. Check harness for damage. 3. Repair or…

view full answer...

Answer 5

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Answer 6

Yes, for just a replacement motor for the Lippert Ground Control 3.0 part #LC358590 you would need the part #LC343758. I confirmed with my contact at Lippert this will replace the motor on your left rear leg.

view full answer...

Answer 7

We do have a replacement motor for the lead leg of the Lippert Ground Control kit you have on your 2016 Reflection 27RL with the part #LC343758 but it sounds like you'd rather do the entire leg assembly with part #LC305340. Since it's a new…

view full answer...

Answer 8

There may be a bunch of different reason why your Lippert Level-Up system has suddenly stopped working. The most common reasons are due to a dead battery, extending your jacks too far, or a blown fuse. The first thing you should check for is the easy…

view full answer...

Answer 9

The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set #LC358590 has 4 35-amp fuses located on the controller. Attched is a complete wiring diagram for you to check out.

view full answer...

Answer 10

It sounds like the fuse that completes the circuit to the right middle jack may be bad. This does happen and will be where I would start. This can be mounted just about anywhere on a trailer/camper, but I included a picture of what it will look like…

view full answer...

Answer 11

If you're getting a RR or LR fault code with your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC358590 or #LC675817, then that is indicating that there is an error at that specific jack (right rear /…

view full answer...

Answer 12

I was able to find the service manual for the Lippert Ground Control 3.0 #LC358590 and found in that where Lippert recommends if the jacks are down for extended periods, it is recommended to spray exposed leveling jack tubes with lubricant every 3…

view full answer...

Replacement Motor for Lippert Components Ground Control 3.0 Auto Leveling System

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching