Height of Timbren Suspension Enhancement Springs with Bracket # TFR250SDJ

Question

Question:

What is the combined overall height of part # TFR250SDJ ? That includes the rubber bumper mounted to the frame bracket.

asked by: Gary

1

Helpful Expert Reply:

The combined height of the Timbren Suspension Enhancement System - Rear Axle # TFR250SDJ is 6-7/8 inches. I went out to our warehouse to measure them for you and also have attached a photo for you to see where the measurement was taken.

expert reply by: Jason S

1

click to enlarge

Answer 1

We have two Timbren rear suspension kits that fit your 2020 Ford F-250 we have the standard duty #TFRTT350J which has a spring height of 3-9/16 inch and a bracket height of 2-3/8 inches. The severe duty #TFR250SDJ is 3-5/8 inches tall and has the…

view full answer...

Answer 2

It is true that the 8,600 lbs capacity Timbren Jounce-Style Springs #TFR250SDJ measures 6-7/8" altogether while the 8,000 lbs capacity Timbren #TFRTT350J for heavy duty (Severe Service Vehicle) applications measure 7" altogether. I went out…

view full answer...

Answer 3

The Timbren #TFR250SDJ you were looking at are the correct Timbren suspension enhancement for your 2021 Ford F-250 Super Duty with the Tremor package and will work well for you. These Timbren jounce springs are progressive load bearing springs, so…

view full answer...

Answer 4

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Height of Timbren Suspension Enhancement Springs with Bracket # TFR250SDJ

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching