Inner and Outer Diameter of the Replacement Mounting Bracket # TJB-MB

Question

Question:

Does it come With the snap ring? If not What is the part number

asked by: Dennis

0

Expert Reply:

The outer diameter of the Replacement Mounting Bracket # TJB-MB that you referenced is 2-1/2 inches and the inner diameter is 2-1/4 inch.

expert reply by: Jameson C

0

Dennis

10/26/2017

Does it come With the snap ring? If not What is the part number

Jameson C.

10/26/2017

The snap ring is available separately as part # SNP-RING but it is not included.

Answer 1

The inside diameter of the snap ring that would be used for the #TJB-2002-B is 2 inches, and the outside diameter is 2-1/4 inches. We offer the replacement snap ring for that jack as part #SNP-RING

view full answer...

Answer 2

It sounds like you're looking for the Replacement Retaining Ring for Snap Ring Swivel Jacks #SNP-RING which has a 2-1/4" diameter and is designed to work with etrailer and Ram trailer jacks.

view full answer...

Answer 3

There is only one bracket needed to install the Round Snap Ring Swivel Jack part #TJB-2001-Z on your utility trailer and the bracket is included with the jack so no additional purchases are necessary. I have pointed this bracket out for you. It will…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Inner and Outer Diameter of the Replacement Mounting Bracket # TJB-MB

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching