Steel Thickness of the Demco 6-Hole Adjustable Channel Bracket # DM66134

Question

Question:

Other items listed here state 1/4inch thick steel used. What is the thickness of this one?

asked by: Troy

0

Expert Reply:

The Demco 6-Hole Adjustable Channel Bracket # DM66134 is pretty thick. The steel thickness used for this is 7/16 of an inch.

expert reply by: Jameson C

0

Answer 1

There sure is; Titan is actually Dexter now, but there is a 6-hole weld-on bracket that you can use with the coupler. The exact parts you need are as follows: - Dexter Bolt-On Coupler for 2 5/16" Ball - Primed - 21K #T4855300 - Demco 6-Hole…

view full answer...

Answer 2

Hey Troy, thanks for reaching out! To replace the 6-bolt channel I recommend installing the Demco 6-Hole Adjustable Channel Bracket #DM66134 which is rated for up to 21K and will need to be welded onto your trailer. If you're needing additional…

view full answer...

Answer 3

Good question; the bolts in the Hardware Kit for Demco Adjustable Channel Mount Couplers #DM6166 should be torqued to 150 lb-ft during install of a Demco coupler like #DM14040-81 to a bracket like #DM66134.

view full answer...

Answer 4

Thank you for the image of your setup Steve. I do not know what the manufacturer was thinking when they welded in the Demco Actuator on your boat trailer. With how it was installed there is no way for you to access that rear pin without drilling a…

view full answer...

Answer 5

First I want to make sure you verify your channel mount for the Demco Trailer Coupler #DM14040-81 has a 21K or larger capacity as often times they are less like the Demco #DM15349-52 which often times people look at and think it is a channel mount…

view full answer...

Answer 6

I think you may have one of the Curt Channels #CU69FR rather than the more standard 3" wide channel on your trailer. This only fits the Curt SecureLatch Lunette Ring #CU99FR. The Coupler #DM12688-95 you found does require a 3" wide inside…

view full answer...

Answer 7

To find the correct replacement axle it is very straight forward. You want to know the Axle weight rating. This is going to be on the sticker found on the cross tube of the axle if this is not present measure the axle tube diameter and that can help…

view full answer...

Answer 8

The recommended hanger kit for a Triple-Axle Trailer Hanger Kit for Double-Eye Springs is part #APTT1. This kit is designed to work on axles with capacities of 2,000 to 7,000 pounds. If your mobile home trailer axle is within this weight capacity…

view full answer...

Answer 9

The wall thickness of the tubing of the Dexter Axle part #7461121 you referenced is .16 inch. This axle comes with the spring seats welded on at 80 inches but you could move them to match what your trailer needs.

view full answer...

Answer 10

The difference between the Grease Seal 10-36 #10-36 and the 10-10 Grease or Oil Double-Lip Seals #RG06-090 is going to be the inner diameter. The #10-36 seal has an inner diameter of 2.250" while the #RG06-090 has a 2.125" inner diameter.…

view full answer...

Answer 11

It is tough to get a correct eye-to-eye measurement on a double-eye leaf spring when the spring is still installed in the suspension. It is much better to measure for a replacement leaf spring by removing it first. Also, if a spring is very old and…

view full answer...

Answer 12

The closest metric trailer tire size to a 4.80x12 is going to be a 145/80-12. The typical diameter of a 4.80x12 tire is 20.5 inches. On a 145/80-12, it is 21.3 inches. So the metric size will be a little over 1/4 inch taller. Make sure to measure the…

view full answer...

Steel Thickness of the Demco 6-Hole Adjustable Channel Bracket # DM66134

Product Page this Question was Asked From

Continue Researching