Availability of 7 foot Brake Line Hose and Kodiak 12

Question

Question:

I have a damaged Kodiak caliper for the 5200 to 6200 lb 12 inch rotor. I believe the mounting bracket is ok. Can I purchase just a caliper and a 7 foot brake hose?

asked by: Kevin

0

Expert Reply:

We do have replacement Kodiak Disc Brake Calipers for the 12" Rotors rated for 5,200-lb - 6,000-lb axles from Kodiak available for you. Part # KDBC225DAC has a Dacromet finish and part # KDBC225S has a Stainless Steel finish - you will simply need to choose the one that corresponds to what you already have on your trailer.

For a replacement 7' Hose you can use part # BH-3MFS-7 from Kodiak which has the 3/16" Male Fittings w/ Stainless Flares already installed for you.

expert reply by: Jon G

0

Answer 1

The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.

view full answer...

Answer 2

The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit you'd want the…

view full answer...

Answer 3

Hi again David; since TDE is no longer around replacement brake pads are not available for the 46304. However, to avoid complete replacement we have found that the Kodiak Disc Brake Caliper #KDBC225DAC will work as a replacement for the 46304. If you…

view full answer...

Answer 4

The caliper itself will typically have information stamped on the casing for the cylinder(see image). Here are some examples of what is stamped on the calipers we carry along with finish on that caliper. Kodiak 225 #KDBC225DAC (Dacroment) Kodiak 225…

view full answer...

Answer 5

Hey David, I've seen reviews of the DeeMaxx #DE86VR fitting, but also others that stated that it won't fit the same mounting hole spacing. We personally haven't had the chance to test this fit out to confirm it yet so I'm more…

view full answer...

Answer 6

According to my research your TDE 46845 trailer hub fits a #84 spindle so the replacement bearing and seal kit you need is part #BK2-100. This is for a single hub so you'll need to adjust the quantity as needed. Attached is a video showing this…

view full answer...

Answer 7

Based on my research a hub with a part number 46845 is a hub with a 5 on 4-1/2" bolt pattern and uses inner bearing #L68149 and outer bearing #L44649 like what the bearing kit part #BK2-100 that you referenced provides. The axle should have…

view full answer...

Answer 8

We do have the Replacement Caliper for Dexter 10" Brakes #K71-773-01 which is a direct replacement for your Dexter K71-773-01 calipers you have currently if you're just looking for those. If not, the Kodiak Disc Brake Caliper #KDBC225DAC…

view full answer...

Answer 9

Hey Brandon, Yes, we do offer the 010-11088 under the Grease Seal Kit- Triple Lip #DX49CR. This comes in a quantity of two seals per kit.

view full answer...

Answer 10

We do sell the caliper but it will come with pads included. I have three options for you listed below depending on your trailer's application: Kodiak Disc Brake Caliper - Dacromet - 3,500lbs to 6,000lbs #KDBC225DAC. - Dacromet plating provides…

view full answer...

Answer 11

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 12

Hey Travis, While we haven't tested DeeMax's compatibility to TDE we have been receiving reviews from people that have tried and found them to be a fit. One review states that they successfully replaced their TDE 46304 calipers with the…

view full answer...