Trailer Grease Seal Recommendation to Replace Seal NOK AB1990E

Question

Question:

I'm sorry, that was AB1990... I mistook the B for an 8.

asked by: Jason B

0

Expert Reply:

We can help you find the seal you need, but the part number you mentioned does not match anything we offer.

Can you get me the inner and outer diameters of the seal? With that I can see what we have that matches.

expert reply by: Jameson C

0

J B.

8/26/2017

I'm sorry, that was AB1990... I mistook the B for an 8.

Jameson C.

8/26/2017

Thanks for getting back to me! What you need is the part # 13194 then. This is the NOK AB1990E just like what you have.

Answer 1

If the existing grease seal on your trailer is in fact the NOK part #AB1990E that you referenced in your question, then I recommend using the Redline Grease Seal #13194 as a replacement. This is a confirmed replacement for the NOK model and the…

view full answer...

Answer 2

For your Dico Hub 45263, you are going to want to use part #L44649 for both the inner/outer bearings and part #168255TB for the grease seal which has a double lip. I was not able to confirm that the hub uses different inner and outer bearings. We had…

view full answer...

Answer 3

The UFP hub that you've referenced isn't made any longer I don't believe, but we do have some options for you. From some previous customers, we've determined that the UFP H-1062-3 axle has a spindle that has #L44649 inner and outer…

view full answer...

Answer 4

It sounds like you either have a blown fuse or a short on the right side turn light and brake light circuit. First, I recommend checking the trailer wire connector on the vehicle. You can use a circuit tester, like #PTW2993, to test that power is…

view full answer...

Answer 5

Hey Glenn, thanks for all of the info on your current hub. From that we know that you have a 2,200 lb axle and the correct hub replacement would be the part #8-258-5UC1-EZ. This is also pre-greased so it's ready to be installed on your trailer.…

view full answer...

Answer 6

To find the correct hub for your axle you typically need to find the part numbers for your bearings and grease seal, or the diameter of the different spots that they sit on your spindle. We actually have had a customer who sent this information in to…

view full answer...

Answer 7

Thanks for the picture! If you can't get your races out, you'll just need the entire new hub assembly #AKIHUB-545-2-EZ-2K which comes with brand new races already installed, new bearings, and new grease seals but you'll need to use #34823…

view full answer...

Answer 8

We've had customers with your Dico 45263 hub in the past get us their bearing numbers so we know that for a replacement with the wheel bolt pattern you need you could use the #AKIHUB-545-2-G-EZ-2K and you'd be set.

view full answer...

Answer 9

We spoke with our contact at UFP Dexter and he said that your 41062 hub uses inner bearing 031-030-02, outer bearing 031-032-02, and seal 010-181-00. This is the equivalent of inner bearing #25580, outer bearing #LM67048, and grease seal #GS-2125DL…

view full answer...

Answer 10

For a replacement of the NOK AB1990E grease seal you'll need the Grease Seal #13194.

view full answer...

Answer 11

When towing a trailer with a trailer sway is more likely than when that second trailer (the Seadoo) is hitched directly to a tow vehicle. This happens because at the rear of a 5th wheel there will be more lateral motion than at the back of a tow…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Trailer Grease Seal Recommendation to Replace Seal NOK AB1990E

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching