Length Measurements for EZ Lube Spindle 2.25
Updated 06/13/2020 | Published 08/24/2017
Question:
I see the stub length is 3 inches to the back of the brake flange. What is the total length, end to end and from brake flange to the threaded end? Thank you
asked by: Keith
Helpful Expert Reply:
I went out to the warehouse to take some measurements of trailer spindle # TRU37FR for you. The stub is actually 3-3/8 inches from the end to the brake flange. It is 3 inches from the end to where the weld is for the brake flange.
The brake flange itself is a hair under 1/4 inches thick.
The distance from the flange to the tip of the grease fitting is 7-1/2 inches. But to the end of the threaded part it is 7-1/4 inches.
The overall length from tip to tip is approximately 11-1/8 inches. (3-3/8 + 1/4 + 7-1/2.)
Product Page this Question was Asked From
#42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles - 2-1/4" Diameter
- Trailer Spindles
- EZ Lube Spindle
- With Flange
- 25580
- 2-1/4 Inch Diameter
- Round
- For 5000 lb Axle
- For 6000 lb Axle
- For 7000 lb Axle
- TruRyde
more information >
Continue Researching
- Shop: #42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles - 2-1/4" Diameter
- Search Results: brake actuator
- Q&A: What Is The Difference Between 7K Hub/Drums From etrailer And Dexter?
- Shop: Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 12" - 6 on 5-1/2 - Pre-Greased
- Shop: #42 Spindle for 5,200-lb to 7,000-lb Trailer Axles - 2-1/4" Diameter
- Q&A: Overall Length of the Demco DM8104311 Surge Brake Actuator
- Shop: Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased
- Shop: Demco Hydraulic Brake Actuator w/ Drop - Drum - Zinc - 2-5/16" Ball - 12,500 lbs
- Shop: Terran Industries Trailer Idler Hub Assembly for 5,200 to 6,000 lbs Axle - 6 on 5-1/2
- Search Results: 5000 lbs axle
- Q&A: Drum Brake Surge Brake Actuator Comparable to Demco DM8104311
- Q&A: Dimensions of Trailer Spindle TRU37FR
- Q&A: Bolt Hole Specs of the Demco Hydraulic Brake Actuator DM8104311
- Search Results: locations
- Shop: Electric Trailer Brake Assembly - Self-Adjusting - 12" - Left Hand - 5,200 lbs to 7,000 lbs
- Search Results: trailer bearings races seals caps
- Search Results: bearing 25580 trailer bearings races seals caps
- Search Results: 25580
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Video: A Closer Look at the Bearing Kit, 14125A/ 25580 Bearings, 10-36 Seal
- Q&A: Replacement Bearing Kit, Spindle Washer, & Nut For 5,200 lb Lippert Trailer Axle
- Q&A: Replacement Spindle and Hub/Drum that Fits Lippert 5,200 lb Trailer Axle
- Shop: Trailer Hitch
- Search Results: brake backing plate
- Shop: Trailer Wiring
- Shop: Tonneau Cover
- Video: Installing the Dexter E-Z Flex Suspension Kit on your 2022 Jayco Jay Feather Travel Trailer
- Video: Installation of the Dexter E-Z Flex Suspension Kit - Enclosed Trailer
- Video: Dexter E-Z Flex Suspension Kit Spec Review
- Video: All You Need to Know About the Lippert Spare Tire Winch with Offset Cable
Jorge R.
6/10/2020
Does it fit with Hydraulic Brake Kit Item # AKFBBRK-7 and Trailer Hub and Drum Item # AKHD-655-6-EZ-K