Will Bulldog Coupler BD028499 Replace Atwood Coupler on ATC Quest Trailer

Question

Question:

I need a new trailer coupler. The current coupler is Item # 81911. The trailer is an ATC Quest aluminum trailer and ATC drilled the atwood so it bolts onto the aluminum a-frame. Will the Bulldog Item # BD028499 fit as a replacement of the Atwood same angle, same underside clearance, etc.?

asked by: Ben F

0

Expert Reply:

The Bulldog coupler part # BD028499 is the same angle as the Atwood coupler you had so it would fit right up to your trailer and work well.

expert reply by: Jameson C

0

Answer 1

Yes, the Dometic FreshJet 3 can typically be integrated with your existing Dometic 2 zone digital thermostat system on your 2019 Newmar Ventana, but it is not a direct plug and play replacement for your current Penguin unit. The FreshJet series is…

view full answer...

Answer 2

Hello Chuck, Great question, and if you could let me know what page the Kevin video is on, I would love to take a look to see exactly what you are referencing. There has been a lot of mixed information in the past about what units the Advents can…

view full answer...

Answer 3

According to Air Lift, there are a few things that can cause the frozen comp error code issue. The problem is likely an air leak between the manifold and the compressor or simply a weak compressor that would need to be replaced. To get the compressor…

view full answer...

Answer 4

There could be a couple reasons this could be happening. One being the hitch ball could be over-sized but I seem to think tightening the lock nut under the wedge will eliminate the need for you to manipulate your hitch ball into the secured position.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Will Bulldog Coupler BD028499 Replace Atwood Coupler on ATC Quest Trailer

Featured Help Information

Miscellaneous Media

Continue Researching