Differences Between Fulton Jacks # FXP10 and # FXP15

Question

Question:

Im in need of a bolt-on Fulton jack preferably with an 8inch wheel and Im looking at the fxp10 vs the fxp15. It appears that they both have the same 12 3/4inch retracted height, is that correct with the Fxp15 having an 8inch wheel vs the fxp10 with a 6inch wheel?

asked by: Tom M

1

Helpful Expert Reply:

The Fulton Jack part # FXP10 does have a 6 inch wheel and a 1,200 lb capacity whereas the # FXP15 has an 8 inch diameter wheel and a 1,500 lb capacity. Aside from that they are very similar. They use the same mounting brackets and same sidewind crank.

They both do have a retracted height of 12-3/4 inches.

expert reply by: Jameson C

1

Answer 1

The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…

view full answer...

Answer 2

The #STL22CCRB lamp you referred to is typically mounted in a grommet, like part #A70GB, which in turn is mounted in a bracket like part #337LB1SS. If you were planning on cutting a hole to mount the lamp and grommet, the hole will need to measure…

view full answer...

Answer 3

I spoke with my contact at Fulton and if your current jack pivots on a 1/2" bolt then you can use either part #FXP10 for a 1,200 lb option or part #FXP15 if you wanted a 1,500 lb option. These come with a bolt on bracket that can fit a 3" x…

view full answer...

Answer 4

I recommend using the Xtreme Off-Road Swing-Up Trailer Jack #ORJW350D as we do not have a jack which will fit the same weld on bracket you have on your boat trailer. This jack can be bolted onto your frame and will allow you to have more…

view full answer...

Answer 5

We do have the Dexstar 15x5" Steel Spoke Trailer Wheel 17-384 listed on our site as part #AM20428. Please note that Destar has this listed with a weight capacity of 2,150 lbs on their site so you need to plan your weight capacities to fit within…

view full answer...

Answer 6

Thank you for the photo of your old wheel. That is extremely helpful in this case.To answer your main question, the measurement of the bolt pattern is going to be the most important factor in replacing the wheels on your trailer. The hub bore…

view full answer...

Answer 7

Thank you for the photos! According to my information and what you sent in, your best option for a replacement fender is the CE Smith Black Fender: CE Smith Single Axle Trailer Fender w/ Top and Side Steps - #CE19503 (Qty 1) CE Smith Single Axle…

view full answer...

Answer 8

We offer weld-on and bolt-on trailer jacks that are similar to the Shelby 5764A jack you wish to replace but the jacks we offer are not exact replacements. We do have a jack that has a mounting plate similar to the Shelby mounting plate., It is part…

view full answer...

Answer 9

Based on the pictures you provided it looks like the mount on your 1999R71 Range trailer uses a jack very similar to the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301. You will need to confirm that this jack will be compatible by measuring the…

view full answer...

Answer 10

The Replacement Handle for Fulton Hand Winch - 9" Long #F501109 is the replacement you are seeking. It will have the oblong hole to allow the cranking of the winch without slipping.

view full answer...

Answer 11

The Hand Winch Strap with Safety Hook, 2" Wide x 20' Long - 4,000 lbs.#DL24242 is needed because the strap is sewn around the hook. If you have a chain or wanted to add a small portion or chain to your hook then you can use the Titan Chain…

view full answer...

Differences Between Fulton Jacks # FXP10 and # FXP15

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching