What Do the Wires of a The Titan Actuator T4750700 Run To
Published 08/09/2017
Question:
The actuator came has two black wires. I usually only see one. im wondering what they go to. Also how do i bleed the brakes.
asked by: Zach
Expert Reply:
The two wires you mentioned are for the reverse lock out solenoid wiring. What you need to do is ground one of them (doesn't matter which), and then run the other to a reverse light circuit and that way the actuator won't activate when you are in reverse and let you back the trailer up.
We happen to have a video on the proper procedure for bleeding trailer brakes. I have attached the video below as well as outline the method here for you.
First top off the master cylinder with appropriate fluid. Next you will want to pump the fluid from the master cylinder. You can do this by unbolting the plate that holds the lever in place and then use that lever to actuate the master cylinder and force the fluid through. On some units, you will have to manually activate it at the point where the hitch ball moves in and out. The model in the video has a lever underneath the unit you could use to actuate it.
Next, find the bleeder valve and open it. Take a rubber hose and slide it onto the bleeder itself and run the other end to a clear container. Using a clear container will allow you to see if any air bubbles rise up during the process. No bubbles means no air and that the system is full of just fluid.
Start on the wheel cylinder closest to the T where it splits off. When you get clear fluid running out through your bleeder valve and no bubbles, you can go ahead and pull it back and hold it there and then shut off the bleeder valve. Continue from the closest wheel cylinder to the T and work your way back to front if you have a dual or triple axle trailer.
Product Page this Question was Asked From
Dexter Zinc-Plated Brake Actuator w/ Drop - Disc - 2-5/16" Ball - Bolt On - 20,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Farm Trailer
- Boat Trailer
- Construction Trailer
- Travel Trailer
- Utility Trailer
- Bolt-On
- 20000 lbs GTW
- 2-5/16 Inch Ball Coupler
- 3 Inch Channel Tongue
- Disc Brakes
- No Lockout
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: titan model 20 actuator
- Shop: Dexter Zinc-Plated Brake Actuator w/ Drop - Disc - 2-5/16" Ball - Bolt On - 20,000 lbs
- Q&A: Replacement Inner Slide for Titan Model 20 Surge Brake Actuator
- Video: The Low-Down on the Replacement Damper for Model 20 Actuator
- Video: Breaking Down the Dexter Zinc-Plated Brake Actuator
- Shop: Dexter Zinc-Plated Brake Actuator w/ Drop, Electric Lockout - Disc - 2-5/16" Ball
- Q&A: Replacement Coupler Recommendation for Titan Model 20
- Q&A: How to Establish Ground Connection When Re-Wiring Aluminum Trailer
- Video: HydraStar Electric Over Hydraulic Disc Brake Actuator Installation - 2020 Grand Design Momentum 5W T
- Shop: Replacement Master Cylinder Assembly for Dexter Model 10 and Model 20 Brake Actuators - Drum
- Shop: Replacement Master Cylinder Assembly for Dexter Model 10 and Model 20 Brake Actuators - Disc
- Shop: Dexter Zinc-Plated Brake Actuator w/ Drop, Electric Lockout - Disc - 2-5/16" Ball - 20,000 lbs
- Shop: Demco Actuator Replacement Master Cylinder for Drum Brakes
- Shop: Dexter Zinc-Plated Brake Actuator - Disc - 2-5/16" Ball - Bolt On - 12,500 lbs
- Video: Review of the Dexter Zinc-Plated Brake Actuator w/ Drop
- Q&A: Is Lockout Solenoid Included With Titan Brake Actuator Coupler # T4750700
- Search Results: kodiak brake pads
- Video: Breaking Down the Demco Hydraulic Brake Actuator w/ Drop
- Video: Let’s Check Out the Kodiak Ceramic Brake Pads
- Video: Comprehensive Review: Dexter Hydraulic Brake Actuator w/ Drop and Lockout Shield
- Q&A: Replacement Brake Kit and Hubs/Rotors For a Continental Trailer With 5,880LB Trailer Axles
- Search Results: c57187
- Q&A: Replace Trailer Surge Coupler with Straight Coupler on a Trailer With Surge Brakes
- Q&A: Recommendation on a Surge Coupler that is Rated to Work on a Trailer w/ Disc Brakes
- Article: How to Bleed Your Trailer Surge Brakes
- Article: Trailer Wiring Diagrams
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Couplers
- Article: How to Measure a Trailer Axle
on Brake Actuator
