Selecting Electric Boat Trailer Winch with Manual Operation Capability

Question

Question:

I am looking for an electic winch for my 22 century walk around. 3800 pounds plus engine. Wondering what model i should purchase and im concerned if these models have a manual backup incase the electric fails. Thanks

asked by: Mike

0

Expert Reply:

Our range of boat trailer electric winches is shown on the linked page. Many electric winches have a manual cranking option, such as the Dutton-Lainson TW4000 StrongArm Electric Marine Winch # DL25200, which is operated using a 5/8-inch deep socket and ratchet.

For a boat/motor weighing in excess of 4000-lbs I suggest the heavy-duty Dutton-Lainson StrongArm Electric Winch # DL25215 which includes a manual crank handle. Winches will last longer when they are used below their maximum capacity. Since this winch can be used with heavier boats it will tend to last longer and provide better service in your application. Please refer to the linked article for more information on selecting an electric winch.

expert reply by: Adam R

0

Steve S.

5/22/2020

Looking for electric and manual winch to load a 24' 4600 lb Down East style hull (OB) onto roller trailer. Need at least 26' of strap(preferred) or cable. Thanks for any advice

Chris R.

5/25/2020

For an electric winch I'd go with the Dutton-Lainson # DL25215 and for a manual model the Dutton-Lainson # DL15440 with Strap # DL24251 will work really well.

Steves

5/25/2020

@ChrisR can longer strap be added? Need 26 prefer30 thanks

Chris R.

5/28/2020

@SteveS Unfortunately we don't have any longer straps that are compatible with these winches.

Answer 1

Generally when picking out a winch for a boat trailer the ratio is 2 to 1 meaning you would need a winch with roughly half the capacity as the weight of the boat. With good rollers and a short winching distance the ratio increases to 3 to 1, but with…

view full answer...

Answer 2

The discontinued Shelby 5407 is a single-speed, 1,700 lb hand winch, and we can get you a replacement with a higher capacity. The best option for that is a winch from Dutton-Lainson: - Dutton-Lainson Hand Winch #DL14881 The #DL14881 is a 3,500 lb…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Selecting Electric Boat Trailer Winch with Manual Operation Capability

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching