Recommended Ball Mount Draw Bar For 1-1/4 Inch Trailer Hitch Receiver With 4 Inch Rise
Updated 02/28/2017 | Published 02/26/2017
Products Featured in This Question
Question:
Good Afternoon: Ive looked around on your website but dont see what I need. Im looking for a drawbar with a 4inch rise to fit into a 1 1/4inch receiver that will accept a ball with a 1inch shank. So far I only see ones that have a 3/4inch hole for the ball. Do you carry the type Im looking for? Thank you.
asked by: Tom P
Expert Reply:
The 3/4 inch diameter is a typical size for the 1-1/4 inch hitch receivers. Normally the 1 inch diameter hitch ball is used on a 2 inch receiver ball mount. I have linked the page to the ballmounts that are available for your 4 inch rise and 1-1/4 inch receiver. I recommend the Sportframe Drawbar 4" Rise 2000 Kit # 3594 which has a 10 inch length from center of hitch pin hole to center of ball with 4 inch rise.
I recommend the 2 inch hitch ball # 19258 or the 1-7/8 inch hitch ball # 19256 to go with this ball mount.
Product Page this Question was Asked From
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Draw-Tite
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
- Shop: 2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Shop: Brophy Anti-Rattle Drawbar, 1-1/4" Hitch, 5-1/2" Rise / 6" Drop, 7-1/4" L, 3.5K
- Shop: Curt Class II Euro Style Drawbar with 2" Ball - 3-1/8" Rise - 3,500 lbs
- Shop: Curt Class II Euro Style Drawbar with 2" Ball - 2-5/8" Rise - 3,500 lbs
- Shop: 2" Hitch Ball - w/ 1" Rise - 1-1/4" Diameter x 2-1/2" Long Shank - Zinc - 6K
- Shop: 2" Hitch Ball - 2" Rise - 1" Diameter x 2-1/8" Long Shank - 6,000 lbs
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Replacement Harness for a Lippert Leveling Control Brain for 4-Point Leveling System
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: My Trailer Hitch Doesn't Fit
- Article: Trailer Wiring Diagrams
- Q&A: Comparing Curt and Draw-Tite Trailer Hitches For 2021 Volkswagen Jetta
- Q&A: How Much Can 2004 Mercury Grand Marquis Tow
- Q&A: Hitch Recommendations for a 2015 Chevy Camaro RS
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Could Curt Hitch For 2002 Volkswagen Golf Fit with Aftermarket Exhaust
- Article: Brake Controller Installation: Starting from Scratch