Replacement Parts for Older Thule Roof Rack Fairings

Question

Question:

Looking for the correct replacement fasteners for my TH872XT Fairing. Thank you.

asked by: Corey M

0

Expert Reply:

If you are looking for the push pin fasteners use # 853-5482. For a replacement bracket use # 853-5477. We also have replacement load bar clip # 8537361 and square bar adapter # 853-7362.

expert reply by: Michael H

0

Answer 1

We do have the replacement square head bolt that fits into the part #8537361 with the #853-208909.

view full answer...

Answer 2

The Replacement Clips 1500056059 #TH22NH are only going to be compatible with the new AirScreen XT models listed below. AirScreen XT for Thule Crossbars - 32" Long #TH62WV AirScreen XT for Thule Crossbars - 38" Long #TH72WV AirScreen XT for…

view full answer...

Answer 3

I was able to locate the "service tickets" you mentioned. It looks like you contacted our customer service chat team. The chat's are on-going/open to an extent. They typically end when the chat is over, but they sometimes follow-up with…

view full answer...

Answer 4

You're in a tough spot as Thule has basically phased out your entire roof rack setup from the feet, to the bars, and the fit kit. I wish I had something I could offer that was simple and easy but based on your situation I would go with option 4…

view full answer...

Answer 5

To remove or install the Railing Foot #753-2157-02 from the cross bar you need to push in the gray latch and slide down the black cover identified by the red arrow in the picture attached. This will allow you access to the allen head bolt to loosen…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Parts for Older Thule Roof Rack Fairings

Products Featured in This Question

Continue Researching