Reverse Lock Out Solenoid Recommendation for DA10 Actuator

Question

Question:

DM 5837, DM 11993, DM 5404?? Which one for a DA10 drum brake setup? Will be ordering the DM 8101522 actuator.

asked by: Stan M

1

Helpful Expert Reply:

If you wanted to install an electric reverse lockout on the DA10 Demco actuator part # DM8102222 you would want the part # DM11993. This is confirmed to fit DA10 actuators like this. When this solenoid has power on it would prevent hydraulic pressure from building in your brake lines and assemblies.

expert reply by: Jameson C

1

Answer 1

The reason there are different actuators for disc brakes and drum brakes is the psi the brakes operate at. Disc brakes operate at a higher psi than drum brakes and either too much or too little pressure can cause damage to the brakes. There are units…

view full answer...

Answer 2

I reached out directly to Demco, who told me that grease should never be used on the 12k disc brake actuator you asked about: - Demco Hydraulic Brake Actuator w/ Drop and Electric Lockout - Disc - Zinc - 2-5/16" Ball #DM8104311 They said the…

view full answer...

Answer 3

The break strength of the strap needs to exceed the weight of your trailer. While this sounds strange, you want to choose a strap based on the lightest item that is being strapped, in this case, the trailer and not your 10,000lb boat. If your trailer…

view full answer...

Answer 4

If you wanted to install an electric reverse lockout on the DA10 Demco actuator part #DM8102222 you would want the part #DM11993. This is confirmed to fit DA10 actuators like this. When this solenoid has power on it would prevent hydraulic pressure…

view full answer...

Answer 5

Yes, if you wanted to install an electric reverse lockout on the Demco actuator part #DM8102222 you would want the part #DM11993. This is confirmed to fit DA10 actuators like this. When this solenoid has power on it would prevent hydraulic pressure…

view full answer...

Answer 6

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

The #DM5939 is only compatible with the DA91 like the #DM8759131. Unfortunately, there is no option for manual lockout on a DA70 like the ##DM72VR. There are two ways you can keep your brakes from locking up with this brake actuator. The first is to…

view full answer...

Answer 9

Hey Carl. To replace the surge brake actuator on your 2012 Jayco Pop-Up camper, I recommend the Demco Hydraulic Brake Actuator item #DM72VR. This actuator fits a 3" wide channel and bolts directly to it. It has a 7,000 lbs capacity, fits a…

view full answer...

Answer 10

There isn't an angle I can give you for when the lockout would be needed; however, if you want to be able to back up as needed you will need a reverse lockout with the Demco Hydraulic Brake Actuator #DM8609502. That said, the Manual Reverse…

view full answer...

Answer 11

Thanks for the picture of your actuator that you are wanting to replace. The Demco Hydraulic Actuator part #DM8609502 would be a great option as it is designed to fit A-frames like yours. It has an 8k capacity, designed for a 2 inch hitch ball, and…

view full answer...

Answer 12

Hello Thor, cool name. Our only option for that is the Demco Hydraulic Brake Actuator w/ Lockout #DM8105422. This will work with disc brakes and will fit your A-frame. You just need to get the ball coupler piece separately, such as the Demco…

view full answer...

Reverse Lock Out Solenoid Recommendation for DA10 Actuator

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching