Measurement Between Holes For Bolt On Channel Tongue Trailer Coupler # CT-3001-Z

Question

Question:

What is the distance between the bolt holes on a new 2inch channel 2inch coupler. Hoping to use existing mount holes. Thank you

asked by: Erik

0

Expert Reply:

On the Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 3,500 lbs, # CT-3001-Z, you referenced the distance between the mounting holes is 3-1/16 inches center to center. It is the same separation for each set. Each hole has a diameter of 1/2 inch. I've attached a picture for reference.

expert reply by: Jason S

0

click to enlarge

Answer 1

The BAKFlip F1 Hard Tonneau Cover #BAK37FR will stick out into the bed approximately 23" when folded to just the first of the four panels. I wasn't able to get an exact dimension for the thickness but was told the panels are about 3/4"…

view full answer...

Answer 2

Hi Jim, The BAKFlip F1 Hard Tonneau Cover #BAK37FR is a confirmed fit for a 2024 GMC Sierra 3500 with an 8' bed and is a quad-fold (4-panel) cover.

view full answer...

Answer 3

I have a perfect fold up bed cover for you that will go great with your new 2022 GMC Sierra 3500. It is the BAKFlip F1 Hard Tonneau Cover item #BAK37FR. This is a custom fit aluminum and fiberglass quad-fold cover that sits inside your GMC Sierra…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Hey Scott. To add a 7-way and 4-way connector to your 2024 GMC Sierra 3500 that can be used at the same time, I recommend the TowSmart ProClass Trailer Connector item #TS49RR. It's going to replace the factory one and mount in the same position…

view full answer...

Answer 9

Hey Les, welcome back. The Lippert Hydraulic Hose item #LC52AX does not include any fittings. This is a 1/4" inner diameter, 1/2" outer diameter orange hydraulic hose rated for high pressure systems up to 3,000 psi. The hose is sold by the…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Mark, we have the RetraxPRO MX part #RT80485 that is a confirmed fit for your 2024 GMC Sierra 3500 long bed. The fit of this is not based on the OEM puck kit as that would not affect anything related to the cover. Are you wanting to cover a fifth…

view full answer...

Answer 12

Hey Gary, thanks for reaching out. Yes, that's actually one of the most common uses for the Victron Orion-Tr Smart Isolated DC-DC Charger #VN56RR when upgrading an RV to lithium batteries. The Orion would be installed inside the trailer, as close…

view full answer...

Measurement Between Holes For Bolt On Channel Tongue Trailer Coupler # CT-3001-Z

Product Page this Question was Asked From

Continue Researching