Suspension Enhancement for 1996 Chevrolet 7.4 Bounder P-Chassis Workhorse Motorhome

Question

Question:

Does P/N SSR-290-54 fit the above application for the rear? If not, do you have sumosprings that will work on this Motorhome?

asked by: Dale L

0

Expert Reply:

SumoSprings Solo Custom Helper Springs # SSR-290-54 will fit your 1996 Chevrolet P32 and they are for the rear axle.

If you axle need suspension enhancement for the front axle you can use the Timbren # TUF100.

expert reply by: Charles S

0

Answer 1

The SumoSprings Solo Custom Helper Springs #SSR-290-54 are 5" tall and 4" wide. The kit does include a 1/2" spacer which is to be used during installation so you will have a total height of 5-1/2".

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hey Donald, for the front axle of your 2019 Ford E-450 RV the SumoSprings kit part #SSF-106-47 is what you will want. This will provide the front suspension an additional 1,000 lbs of suspension support which will help with handling and sway…

view full answer...

Answer 6

Hey Alex, thanks for the picture! There's two options for Timbren setups that fit your 2019 Ford Transit T250 and either one of them are really going to help support the rear end of your van when it's loaded up. Which one you need is going to…

view full answer...

Answer 7

Hi Aaron, I can understand not like the TImbrens as those can definitely be rough on a pretty consistent basis; you made a nice choice for your 2024 Ram 3500 by instead going to the SumoSprings Solo Custom Helper Springs #SSR-312-54. The #SSR-312-54…

view full answer...

Answer 8

Hello Andrew, Well that sounds like quite the fun trip, what state or states will you be traveling through? You're asking a really important question, especially since you're planning a cross-country trip with about 250 pounds of bikes and…

view full answer...

Answer 9

According to my research, your 2001 Airstream Land Yacht 30 is on a P-30 Workhorse Chassis. If this is the case then I do have an option for you but SuperSprings does not offer a set SumoSprings Solo Custom Helper Springs that will work on the front…

view full answer...

Answer 10

If it were me I would install the Timbren springs #TFREXC4 on the 2000 Ford Excursion 4x4 instead of the SumoSprings #SSR-109-40. First is the cost benefit; the Timbren springs cost less. There is also the capacity difference. The Timbren springs are…

view full answer...

Answer 11

Hello Mike, thanks for reaching out. Is the rear of your van sagging at all? The SuperSprings Custom Suspension Stabilizer and Sway Control Kit #SSA43 is more for reducing sagging which will in turn help with stability, handling and sway reduction.…

view full answer...

Suspension Enhancement for 1996 Chevrolet 7.4 Bounder P-Chassis Workhorse Motorhome

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching