Bearing Kit Recommendation for 6k Lippert Trailer Axles

Question

Question:

My Fifth wheel has 6000# lippert axles. Do you sell domestic Timken Bearing kits.

asked by: Mark E

0

Expert Reply:

We have two bearing kits that would possible work for a Lippert 6k axle. The part # BK3-100 has bearings 15123 and 25580 plus seal 10-36. This would be the kit for if your spindle has a bearing surface that is 2.250 inches.

If instead your seal surface is 2.125 inches you would need the part # BK3-110.

We don't carry Timken bearings which aren't commonly seen on trailer hubs.

expert reply by: Jameson C

0

Answer 1

We do have the correct trailer hub fit for your Lippert 6,000 lb axle. The hubs for your axle use inner bearing 25580, outer bearing 15123 and a grease seal with a 2.125" inner diameter, and the compatible hub is the Dexter Trailer Hub and Drum…

view full answer...

Answer 2

Unfortunately, I cannot find the axle information for your trailer which would identify the bearings and seals. You will need to pull apart one of your hubs to check the parts for identification numbers or to measure your spindle with a Caliper…

view full answer...

Answer 3

After speaking with EZ Loader what you have on your trailer is a 3,700 lb axle. From what they said the axle was upgraded even though your overall trailer capacity is 3,100 lbs. Although this uses the same #L44649 outer and #L68149 inner bearings,…

view full answer...

Answer 4

In order to find if the Dexter 10" Hub-and-Rotor Assembly #K08-435-05 will fit your 2000 620 Ranger boat trailer you will need some additional information. This assembly is designed to fit a 3,500 lb axle with the standard #L68149 inner and…

view full answer...

Answer 5

It is likely you can use the Trailer Idler Hub Assembly for 3,500 lb Axles #AKIHUB-5475-35-K as it has the most common bearing and seal for 3,500 lb axles, but you'll need to verify this as we don't have any way of knowing the exact hubs that…

view full answer...

Answer 6

Really it's going to boil down to which spindle type your Bayliner Capri has. The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles #AKIHUB-545-35-G-EZ-K will work with 3,500-lb Dexter E-Z Lube and etrailer Easy Grease trailer axles with #84…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Bearing Kit Recommendation for 6k Lippert Trailer Axles

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching