Is Right Hand Version of Submersible Trailer Tail Light ST57RB Available

Question

Question:

I only seem to find the left hand light. Do you hve the right hand? Or are they universal. JIM

asked by: James C

0

Expert Reply:

We do offer the right hand version of the # ST57RB light. Part # ST56RS would feature the same functions as the left tail light, but does not include a license plate illuminator.

I would recommend using some electrical tape and some dielectric grease, part # 11755, to make the installation as clean and secure as possible.

expert reply by: Sarah L

0

Answer 1

I looked up your discontinued Dometic DOTR12CBIV and was able to find that it measures 16-1/8" tall x 22" wide x 16-5/8" deep so the closest replacement option we have is the Greystone Standard RV Microwave w/ Trim Kit #324-000106.…

view full answer...

Answer 2

The Easy Grease Trailer Hub and Drum Assembly #AKHD-865-7-1-EZ-K matches the specs for your Axletek BD-865-37 hub. This hub has an 8 on 6-1/2" bolt pattern with 9/16" lug nuts and studs. It uses the Inner Bearing #25580 and Outer Bearing…

view full answer...

Answer 3

Did you mean to say that your motorhome was built on the F550 chassis? According to the literature I found online, that's the chassis that Newmar built the 2016 Baystar Sport 2903 on. If that's the case, you've likely missing the fuse…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Is Right Hand Version of Submersible Trailer Tail Light ST57RB Available

Products Featured in This Question

Continue Researching