Distance From Rear Edge Of Demco Channel Tongue Trailer Coupler To Mounting Hole

Question

Question:

What is the measurement from the outside edge of this coupler to the mounting holes?

asked by: Laura

1

Helpful Expert Reply:

The distance from the rear mounting hole to the end of the Demco Channel Tongue Trailer Coupler, part # DM13203-95 is 1-3/4 inches.

I have attached a photo of the coupler with the dimension shown you can check out.

expert reply by: Jeffrey L

1

click to enlarge

Answer 1

The Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes #HS481-8067 is designed to be completely plug-and-play so the female end of the 7-way would need to connect to the 7-way cable that's already installed on the trailer…

view full answer...

Answer 2

As your trailer has a 4-way you simply need an Adapter #PK12716 to connect to the Hydrastar Vented Marine Electric Over Hydraulic Actuator #HS481-8067. The actuator, breakaway battery and module will all plug into each other through the included…

view full answer...

Answer 3

Hello Mark, thanks for reaching out. The Demco Channel Tongue Trailer Coupler #DM13203-95 can absolutely be painted. People do this all the time to match the rest of the trailer. There is really no "by the book" process for painting them,…

view full answer...

Answer 4

You are correct, all someone would need to do is cut the metal rods you pointed out to be able to slide the sleeve back of the coupler. Because of that you might be more interested in a Demco Coupler #DM13203-95 which uses a much more concealed latch…

view full answer...

Answer 5

It's possible. Here's Cargo Towing Solutions troubleshooting procedure for if the actuator won't run, or runs continuously: Verify that the trailer and tow vehicle are wired according to the electrical schematic shown below. Perform the…

view full answer...

Answer 6

The HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness #HS381-9067 is designed to work with an aftermarket electric over hydraulic brake controller. This kit will require you to wire in the components using the wire…

view full answer...

Answer 7

We do offer a few repair kits for 2-5/16-inch straight channel couplers, such as parts #DM6008 and #DM5817 for Demco couplers. These and all other repair kits are shown on the linked page. If you find you need to replace your straight 2-5/16-inch…

view full answer...

Answer 8

Here is what you will want to do. Since your 12 volt accessory circuit is only rated for 20 amps you are going to want to run a 10 gauge wire like the part #10-1-1 (sold by the foot) from the positive battery post of your vehicle through a 40 amp…

view full answer...

Answer 9

On the Demco Channel Tongue Trailer Coupler #DM13203-95 the three top row mounting holes' centers are 1-inch from the top flat surface of the coupler. I went to our warehouse and took this measurement to confirm. This and other dimensions are…

view full answer...

Answer 10

The diameter of the holes on the Demco coupler #DM13203-95 that you referenced are 1/2 inch.

view full answer...

Answer 11

Hey John, thanks for reaching out. You will want to use some 1/2" grade 5 bolts and locknuts for mounting the Demco Channel Tongue Trailer Coupler #DM15945. Since the current coupler uses only 2 bolts, you will be fine to use two bolts with the…

view full answer...

Answer 12

The Demco Channel Tongue Trailer Coupler - eZ-Latch #DM15945 is designed for a 3"x3" tube.

view full answer...

Distance From Rear Edge Of Demco Channel Tongue Trailer Coupler To Mounting Hole

Product Page this Question was Asked From

Continue Researching