Galvanized U-Bolt and Plate Recommendation for 1-3/4 inch Round Axle
Updated 08/24/2016 | Published 08/23/2016
Products Featured in This Question
Question:
I am rebuilding a boat trailer to be used in salt water. I am concerned about rust long-term. I am looking to get my 1-3/4inch round axle mounted onto my leaf springs. So my question... are these parts galvanized? APUBR-10 and TRSS175 Thank you,
asked by: Eric
Expert Reply:
For a galvanized U-bolt for a 1-3/4 inch axle you would want the part # CE15285GA. For a galvanized plate then you would want the part # CE20023G.
The part # TRSS175 is not galvanized since it is weld-on application and welding galvanized metal can be dangerous to breathe.
Product Page this Question was Asked From
Spring Seat for Typical 2,000-lb, Round Trailer Axles with 1-3/4" Diameter - Qty 1
- Trailer Suspension Parts
- Spring Seats
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Round Axle - 1-3/4 Inch
- TruRyde
more information >
Continue Researching
- Video: Let’s Check Out the CE Smith U-Bolt Kit for Mounting Round Trailer Axles
- Shop: CE Smith U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4" Long U-Bolts - Zinc
- Q&A: Torque Spec for U-Bolts on 2K Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 60" Long
- Q&A: U-Bolt Kit for Smaller Round Axle on Jet Ski Trailer
- Video: Ultimate Overview of the Single-Axle Trailer Hanger Kit for 1-3/4" Slipper Springs
- Video: Trailer Axle with Idler Hubs Spec Review
- Video: Ultimate Overview of the CE Smith Replacement U-Bolt w/ Nuts for 1-3/4" Round Axles
- Q&A: How to Determine Correct Replacement Slipper Springs
- Shop: Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,000 lbs
- Shop: Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,000 lbs
- Shop: CE Smith Trailer Axle Beam with Standard Spindles - Galvanized - 57-1/2" Long - 1.8K
- Shop: 2-Leaf Slipper Spring w/ Flat End for 1,800-lb Trailer Axles - 30" Long
- Shop: Single-Axle Trailer Hanger Kit for 1-3/4" Slipper Springs - 1-1/2" Tall Front
- Shop: 3-Leaf Slipper Spring w/ Flat End for 2,900-lb Trailer Axles - 30" Long
- Video: In-Depth Review of the CE Smith U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles
- Q&A: Torque Recommendation for 3/8 Inch Diameter Trailer Suspension U-Bolts
- Article: How to Replace Trailer Leaf Springs in 5 Steps
- Q&A: Trailer Suspension U-Bolt and Shackle Bolt Torque Values
- Q&A: Trailer Wheel Torque Spec Chart
- Q&A: Replacement Parts for 1987 Trailer
- Article: How to Measure a Boat Trailer Axle
- Article: How to Raise Your Travel Trailer Height
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: Slipper Spring Trailer Suspension System Review
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: How to Tell the Weight Rating of a Trailer Axle