Sidewinder Options to Replace a Lippert 1621 Pin Box

Question

Question:

Im considering replacing my Lippert 1621 pin box with a side winder turret and pin box. I see so many part numbers offered what would be the correct numbers? Can you provide a list of Sidewinder numbers and fitments? Thanks

asked by: John M

0

Expert Reply:

There are two options for Sidewinders to replace a Lippert 1621 pin box. For a 16k rated Sidewinder we have the part # RP61422. If you need more capacity than that you would want the 19k version which is part # RP34FR.

The first option listed above is an air-ride, cushioned Sidewinder that will offer a much smoother ride with its fully enclosed, custom-tuned air spring in air ride trailer coupler that cushions and absorbs shock.

expert reply by: Jameson C

0

Justin G.

4/20/2020

I have a momentum toyhauler M394 with a lipp 1621HD pin box GVWR 18000 lbs. The momentum GVWR 17000 lbs hitch weight 2925lbs. Towing with 2019 F350 diesel 6.7 short bed 6 1/2 ft. crew cab. 5th wheel hitch in bed is husky 26KW. What do you recommend for my rigs? Reese sidewinder

Reply

Chris R.

4/21/2020

To replace the 1621HD pin box on your trailer, the Reese Sidewinder # RP34FR will work perfectly. It has the capacity needed for this trailer size and will do a great job of providing all the turning clearance you need.

Reply

Answer 1

You can absolutely remove your Rota-Flex pin box and replace it with a Reese Sidewinder without any issue. It will work superbly on your standard bed F-350 and allow you to go from a sliding hitch to a fixed hitch. The pros are the convenience the…

view full answer...

Answer 2

The dimensions I could find for a Norcold 1210 fridge are 68.88 T x 37.88 W x 28.75 D. The closest 12v fridge we carry to this size would be the Everchill RV Refrigerator w/ Freezer Drawer #WAY44FR, which is 28-1/2" wide x 72" tall (at…

view full answer...

Answer 3

Since a Sidewinder like the 20K #RP34FR is a pin box replacement it won't void the warranty of your 2020 Jayco Talon 403T. With that being said, we do want to make sure that you get the correct one that fits your 5th wheel. The pin box that you…

view full answer...

Answer 4

To replace your PowerGear slide out motor part number 531087 you'll need our part number LC87AF, which can only be purchased by either calling in to our customer service department at 1-800-940-8924 or ordering it directly from Lippert.

view full answer...

Answer 5

At this time we no longer offer the Atwood line of AC units so the only available options would be from Furrion or Advent Air. If you're just wanting to replace the rooftop unit and maintain use of your air distribution box and thermostat…

view full answer...

Answer 6

It took a little digging but I found the replacement slide out motor for your Dexter VT00310R and it is the part #LC368417.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 10

That depends largely on the measurements of the trailer nose and whether or not it has an extended pin box. Here is a formula though that you can use to determine if you have clearance. The formula you are referring to is this: (A + B) - C =…

view full answer...

Answer 11

You need to use the following calculation to find if you have enough clearance: (A + B) - C = Clearance A = Distance from the gooseneck ball to the truck cab B = Offset used C = Width of the nose of the trailer divided by 2. So your A is 35" and…

view full answer...

Answer 12

The correct wedge kit for the Curt Crosswing Lightweight 5th Wheel Trailer Hitch #C86JR is the Sidewinder Wedge for Curt CrossWing 5th Wheel Trailer Hitch #C85DR.

view full answer...

Sidewinder Options to Replace a Lippert 1621 Pin Box

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching