What Is Inside Dimension Of Demco A-Frame Trailer Coupler w/ Jack Hole That Fits Trailer Frame

Question

Question:

If back of unit is 10-3/4inch with 50degree mount what is nose width measurement where front of frame butts up to unit ?

asked by: Bill

0

Expert Reply:

The inside dimension of the Demco A-Frame Trailer Coupler w/ Jack Hole, part # DM14791-97 is 2-12 inches.

I have attached a photo of the underside of the coupler with the dimension noted for you.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

Yes, the 40" Vinyl Coated Safety Cables with Clevis Hook (Qty. 2) by Dutton-Lainson, 6,500 lbs is labeled under Item #DL20119. This product is a pair of 5/16 " vinyl-coated cables with safety hooks at one end. These are for use on trailers…

view full answer...

Answer 2

I recommend having the Demco A-Frame Trailer Coupler #DM14791-97 welded on in place of the Sleeve-Lock #CA-5196-B style coupler that you currently have. This Demco coupler uses a 2" hitch ball the same as your current coupler and is rated for up…

view full answer...

Answer 3

The Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs #JSP-100 you mentioned is 1/8" thick, has a hole diameter of 2.29", 8-3/4" long at the back, 5-1/2" long at the front, the diagonal sides are 3-7/8", and…

view full answer...

Answer 4

The A-Frame Trailer Coupler #CA-5210-B will have the exact same yoke latch as your current Ram coupler, so it will not be adjustable, unfortunately. With that said, if you were over doing the weight capacity and can swing the Dutton Lainson A-Frame…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What Is Inside Dimension Of Demco A-Frame Trailer Coupler w/ Jack Hole That Fits Trailer Frame

Continue Researching