How To Install The Brophy Trailer D-Ring Tie Down, # RR5K, On A Wood Trailer Floor
Updated 09/30/2010 | Published 09/28/2010 >
Question:
Do you have illustrations on How to install it on wood trailer floor with or without underlying steel frame members ?
asked by: JOHN E
Expert Reply:
You can attach the Brophy Recessed Trailer D-Ring Tie Down with Backing Plate, # RR5K, most anywhere on a trailer. The recessed D-Ring is designed to be recessed in a wood surface (floor, wall) and using the steel backing plate will make a stronger tie down point.
To be able to recess the tie down ring in the wood you will have to drill a 3-1/4 inch hole in the wood and then, using the backing plate as a template, drill the 4 holes for the mounting bolts. Then, with the steel backing plate over the hole and the mounting holes lined up you can attach everything with the included nuts and bolts.
You will need to locate the tie downs on your wood floor so you will not be drilling into the steel frame when drilling the large 3-1/4 inch hole for the tie down ring to sit in.
I do not have any instructions or illustrations that show how to install the Brophy tie-down and backing plate.
Product Page this Question was Asked From
Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Trailer Tie Down Anchors
- D-Rings
- Universal
- Zinc-Plated Steel
- 1600 lbs
- Bolt-On
- Folding
- Recessed Mount
- Brophy
more information >
Continue Researching
- Shop: Fifth Wheel Hitch
- Shop: B&W Patriot 5th Wheel Trailer Hitch w/ Slider for Dodge Ram - Dual Jaw - 18,000 lbs
- Search Results: 146a
- Search Results: tekonsha trailer breakaway kit
- Search Results: dot tape
- Search Results: 2010
- Search Results: piano hinge trailer door hinges
- Shop: Vehicle Tow Bar Wiring
- Search Results: ram jack
- Shop: Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 6" Drop - 8.5K GTW, 850 lbs TW
- Search Results: 182400
- Shop: Trailer Hitch
- Shop: etrailer Self-Contained Hydraulic A-Frame Trailer Jack - 24" Lift - 8,000 lbs - Bolt On
- Shop: Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-3/4 - Pre-Greased
- Shop: Replacement Switch for Curt Soft Trac I and II Trailer Breakaway Kits
- Shop: Peterson Clearance and Side Marker Trailer Light - Submersible - Incandescent - Round - Amber Lens
- Shop: Camper Tie-Downs
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Can Weight Distribution System Be Used On 2007 Toyota FJ Cruiser With OEM Hitch?
- Q&A: How to Connect a Charge Line to a 7-Way Connector?
- Q&A: How to Connect a Charge Line to a 7-Way Connector
- Video: Review of Weigh Safe Replacement 2 inch Hitch Ball - WS96KR
- Video: A Closer Look at the Weigh Safe Ball Mount Replacement 2" Hitch Ball
- Video: Review of Weigh Safe Dual Locking Pin And Hitch Receiver Lock - WS22KR
- Video: A Closer Look at the Weigh Safe Dual Locking Pin and Locking Hitch Lock Set
- Q&A: Can I Use a Weight Distribution Hitch Without the Weight Distribution Bars Installed?
- Q&A: Is 2 Inch Hitch Ball Okay to Use With 2-5/16 Inch Coupler
- Q&A: Can Weight Distribution System Tow Trailer without Spring Bars Connected
- Video: Brophy D-Ring Tie Down Anchor w Backing Plate: The Breakdown

