Hubs, Brake Assemblies and Brake Controller to Use with Timbren Axle Less System ASR2KHDS03
Published 07/19/2016
Products Featured in This Question
Question:
good Morning, Will you please recommend all of the parts I would need to get a 2000lb timbren suspension installed on a trailer. I am using VW wheels. I believe the hole pattern is 5 lugs at 4.5. Ideally, from the bottom of the frame of the trailer, the center of axle is 5. A 4inch will work as I can adjust the fit as necessary. The face of the hub that the inside of the rim sits against is 6.5inch out from the outside edge of the trailer frame. More is fine. Too much less than that and I will be adding more steel than I want . Ill need the bearings as well as a brake set up and any other suspension related pieces to pretty much bolt this on and roll down the road. I plan to use an electric brake controller so any suggestions there would be appreciated.
asked by: Karl K
Helpful Expert Reply:
The Timbren Axle Less System part # ASR2KHDS03 that you referenced will weld or bolt on to the trailer frame. Hardware for that is not provided.
For hub/drums to fit the included spindles you would want the part # AKHD-545-35-EZ-K and then for brake assemblies you would want the part # 23-27 for the right hand side and part # 23-26 for the left hand side. The hubs are for a 5 on 4-1/2 inch bolt pattern.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes.
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 4" Lift - 4 Bolt - 2K
- Trailer Axles
- Rubber Spring Suspension
- Standard Grade
- No Hubs
- 2000 lbs
- Spindles Only
- Universal Fit
- Lift - 4 Inch
- Timbren
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Q&A: 10 Inch Electric Trailer Brakes with Parking Brake Feature
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 4" Lift - 4 Bolt - 2K
- Shop: Timbren Axle-Less Trailer Suspension w/ Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 2K
- Shop: Easy Grease Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 5 - Pre-Greased
- Q&A: Can Parking Brake Be Added To Electric Trailer Brakes Not Equipped With Parking Brake Feature
- Search Results: akebrk~35~sa
- Shop: Dexter Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Shop: Electric Trailer Brake Assembly - Self-Adjusting - 10" - Left Hand - 3,500 lbs
- Shop: Dexter Parking Brake Kit with Breakaway for Hydraulic Drum Brakes
- Q&A: Replacement Foot Plate for a Lippert Jack 359278
- Q&A: Recommended Timbren Axle-Less System with 5 on 5 Bolt Pattern Hubs for Overland Trailer
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Is There a 3,500 Lb Idler Hub with Hub Bore Less Than 64MM
- Q&A: Comparing Timbren Axle-Less 2K Trailer Suspension Systems with 4" Lift
- Q&A: Timbren Axle-Less Trailer Suspension Compatibility with Jeep 5 on 5 Bolt Pattern
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Tire Sizing
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: How to Raise Your Travel Trailer Height
- Article: How to Measure Your Trailer Wheel Bolt Pattern