What is the Smallest Diameter Hitch Ball

Question

Question:

Looking for a hitch ball 1 inch and need a coupling to go on it smallest Ivan find is 17/8 I though that I had seen one somewhere Maybe for golf carts lawn mowers 4 wheelers

asked by: Randy

0

Expert Reply:

The smallest diameter hitch ball we have is actually 1-1/4 inches in diameter and is designed for use with friction sway control systems like # 83660.

The threaded shank diameter of this ball is 5/8 of an inch.

expert reply by: Jameson C

0

Mark

4/15/2020

I have a vintage camper that uses a 1 3/4 ball. Anything in stock? Thanks

Chris R.

4/16/2020

Unfortunately we don't have a 1-3/4" hitch ball available, and this might be pretty hard to come by elsewhere. I think your best option may be to replace the coupler with a modern sized unit. If you decide to go this route, I linked our full selection of couplers below that you can look through.

Helpful Links

trailer-coupler

Answer 1

Sway control is designed to be used in situations where the trailer sways under adverse conditions such as high winds or when large vehicles are passing causing the trailer to become unstable. Sway control also helps if you have to maneuver suddenly.…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What is the Smallest Diameter Hitch Ball

Continue Researching