Do Bearing Buddy Bearing Protectors Come with the Rubber Covers

Question

Question:

Good morning, Just wanting to confirm the BB1938 includes the covers with the bearing buddies. Thanx!

asked by: John B

0

Expert Reply:

Yes indeed. The Bearing Buddies, such as # BB1938, do come with the little bras/rubber covers. I have included a picture showing all for parts for you.

Should you ever need some replacements in the future we have those, too; # BB19B.

expert reply by: Michael H

0

click to enlarge

Answer 1

Hey Booby, it looks like Timken bearings like the Timken Replacement Trailer Wheel Bearing #TMK29FR are made in 33 different countries like Romania, Mexico, and the United States, so there is no real way of knowing where these came from because they…

view full answer...

Answer 2

An EZ lube spindle will be better because it allows you to insert grease from inside the spindle where the bearings are and push out the old grease whereas with a Bearing Buddy you basically just get to push grease through the front of the hub. I…

view full answer...

Answer 3

Each of the trailer idler hubs with a 5 on 5" bolt pattern are a fit for 3,500 lb axles and use inner bearing #L68149 (1.378" inner diameter), outer bearing #L44649 (1.063" inner diameter), and grease seal #58846 (1.719" inner…

view full answer...

Answer 4

The trailer hub part #84550BX has a 5 on 5 inch bolt pattern, for a hub that would fit the same spindle that has the 5 on 4-1/2 inch bolt pattern you would want the part #84545BX. See review video. I attached a page that has all of the trailer rims…

view full answer...

Answer 5

The Dexter "8-256" is a hub assembly that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in a few different bolt patterns therefore you would need to confirm your bolt pattern using the attached help…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The only potential issue I can see happening is if the converter in your 2017 Lance 1475 camper isn't rated for lithium batteries. If that's the case then we have the Progressive Dynamics Replacement Section for AC/DC Power Distribution Panel…

view full answer...

Answer 8

It is not required to grease the rubber portion of hub seals like the #GS-2250DL that you referenced. You would not need to do that with the races either.

view full answer...

Answer 9

This is possible assuming the bearings match up with the spindle on your current axle. All of our idler hubs and hub and drum assemblies with a 5 on 5 bolt pattern use a #L44649 outer bearing and #L68149 inner bearing. You will need to either find…

view full answer...

Answer 10

I think the best way to explain how to install a grease seal like #10-9 is to take a look at the video I have linked. Go to about the 6 minute, 10 second mark. At this point in the video, our installer begins to install the seal in the back of the…

view full answer...

Answer 11

First, make sure that you have the correct size Bearing Buddy. It should be slightly larger than the hub bore though it is difficult to tell just by looking. If you can tell me the outer bearing number I can determine which is the correct model.…

view full answer...

Answer 12

Since a larger diameter wheel and tire would spin slower at the same MPH than a smaller diameter wheel/tire yes, in theory a larger diameter wheel/tire is easier on bearings. That said, we don't see smaller setups wear out at a noticeably faster…

view full answer...

Do Bearing Buddy Bearing Protectors Come with the Rubber Covers

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching