Does the Trailer Brake Vented Magnet for Hayes and AL-KO 12-1/4" x 3-1/2 Attach to Actuating Arm

Question

Question:

Do the BP01-285 magnet directly replace the original magnet as far as mounting to the swing arm or do I need to replace the arm to an updated version to use the new magnet.

asked by: Mike

1

Helpful Expert Reply:

The Trailer Brake Vented Magnet for Hayes and AL-KO 12-1/4" x 3-1/2" Electric Brakes # BP01-285 come with everything needed to attach the magnets to the actuating arm of your current assemblies. You wouldn't need to replace the arms as well.

expert reply by: Jameson C

1

Answer 1

To replace the Trailer Brake Vented Magnet #BP01-285 on your Electric Brake Assembly like part #10259 you will need to disconnect the wiring from where it is connected to the rest of the wiring on your trailer and then use the clip that came off of…

view full answer...

Answer 2

It sounds like your trailer brakes are sticking, but I doubt the problem is the brake controller. However, you can test this by applying the brakes like you normally do while coming to a stop. Once the trailer and vehicle stop get out and unplug your…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Does the Trailer Brake Vented Magnet for Hayes and AL-KO 12-1/4" x 3-1/2 Attach to Actuating Arm

Product Page this Question was Asked From

Continue Researching