Adjusting the Angle of the Head on an EAZ Lift Weight Distribution System
Updated 04/02/2015 | Published 04/01/2015
Question:
Eaz-Lift 1200 lb. hitch adjustment screw I am using the above hitch on my 2005 Ford Expedition 5.4L. How do I use the adjustment screw on my hitch to maintain the angle of the head?
asked by: Malcom
Expert Reply:
We do not carry the Eaz-Lift systems but I do know exactly what you are talking about. The bolts that hold the head to the shank would have to be loose and the adjustment screw turned in the desired direction. Tilting the ball towards the trailer puts less tension on the spring bars. Tilting it towards the tow vehicle puts more pressure on the spring bars.
It can also be used to fine tune the ride height to help get everything level.
Product Page this Question was Asked From
Reese Strait-Line Weight Distribution w/ Sway Control - No Shank - 12 lbs GTW, 1,200 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Trunnion Bar
- Shank Not Included
- Top-Mount
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- Allows Backing Up
- 1000 lbs
- 1100 lbs
- 700 lbs
- 800 lbs
- 900 lbs
- Reese
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: eaz lift
- Search Results: brakes
- Article: How to Install a Weight Distribution Hitch (With Pictures & Video)
- Shop: Replacement Key for FIC Locks - HF302 - Qty 1
- Video: Review of Thetford Replacement Water Module Assembly - TH64UE
- Shop: Progressive Dynamics 4000 Series Mini RV Converter w/ Charge Wizard and AC/DC Distribution Panel
- Video: Curt Weight Distribution Head Angle Adjustment: The Breakdown
- Shop: Replacement Water Module Assembly for Thetford Aqua-Magic V and Aqua-Magic VI RV Toilets
- Shop: Curt Round Bar Weight Distribution System w/ Friction Sway Control - 10K GTW, 1K TW
- Shop: Curt Head Angle Adjustment Kit - For Trunnion-Style WD Hitches - Bolt, Washers, Clip - 1,500 lbs TW
- Shop: Replacement Snap-Up Lever for Equal-i-zer Weight Distribution Systems
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Q&A: Adjusting Head Of Husky Center Line Weight Distribution Hitch To Level Spring Bars
- Q&A: 2 1/2 Shank Recommendation for Use with the Husky Center Line HT32218 WD System
- Q&A: Adjusting Husky Center Line Weight Distribution System For More Level Ride And Sway Control
- Q&A: Troubleshooting Weight Distribution Hitch Setup And Transferring Additional Weight To Front Axle
- Video: The Low-Down on the Replacement Velcro Strip for Access TonnoSport and Vanish Covers
- Video: Truxedo Tonneau Covers TX1115174 Review
- Video: An In-Depth Look at the Replacement Velcro Strip for Access Tonneau Covers
- Video: Review of Truxedo Replacement Shur-Bond Velcro Brand Fastener Strips 6 Foot Bed - TX1117786
- Video: Ultimate Overview of the Lippert On-The-Go Telescopic Ladder
- Search Results: stabilizers
- Q&A: TireMinder TPMS Sensors Compatibility With Vehicle Display
- Q&A: How Many Washers Should be Used with the Husky Center Line WD # HT32217 for a 5,980 lb Trailer
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: 5 Things to Know About Weight Distribution Hitches
- Search Results: trailer jack
- Article: How to Measure for Trailer Hitch Drop
- Article: The 5 Best Trailer Drop Hitches You Can Buy
on Weight Distribution Hitch
