Winch Recommendation for Installing Handle on Either Side of the Winch

Question

Question:

Do you have a hand crank winch that you can operate with left hand? thanks

asked by: Barry B

0

Expert Reply:

Yes, the Fulton F2 Fully Enclosed Trailer Winch # FW16000101 can have the handle of the winch easily installed on either side of the winch so it should work very well for you.

I attached a review video for more info for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I really like the Dutton-Lainson Covered Hand Winch #DL17048 for your 2003 Ranger 205 boat because it's covered to it looks more sleek, and it has a 1,900 lb weight rating which means it can easily handle the weight of your trailer even if you…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 8

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 9

Hey Dave, for a saltwater boat trailer, powder-coated wheels wouldn't be my first choice, but they can still last quite a while if you're good about rinsing them thoroughly after each launch and sealing any chips or cracks in the finish as…

view full answer...

Answer 10

Hey Steven! The etrailer Rust-Resistant 3-Leaf Double Eye Spring for 4K Trailer Axles - 25-1/4" Long - Dacromet #e93SR will be adequate for your 2020 Gulf Stream Vista Cruiser since the Dexter D40 number correlates to a 4,000 lbs hub and drum…

view full answer...

Answer 11

Hello Randy, Great question. For replacing bunk boards on a 20 ft bass boat trailer (like #CE27845), you’ll want 3/8 inch diameter lag bolts that are 1-1/2 to 2 inches long, depending on the thickness of your bunk brackets. Go with hot-dipped…

view full answer...

Answer 12

Hello Chad, thanks for reaching out. The CE Smith Roller Style Guide-Ons for Pontoon Boat Trailers #CE27672 will work fine with a StarCraft tri-toon, assuming you’ve got a pretty standard bunk-style trailer under it. We’ve put those on plenty of…

view full answer...

Winch Recommendation for Installing Handle on Either Side of the Winch

Featured Help Information

Miscellaneous Media

Continue Researching