Diameter of Tubing Used in the Firestone Ride Rite Air Suspension Kits

Question

Question:

Do all firestone rife rite use 1/4 npt size?

asked by: Tyler

0

Expert Reply:

Yes, all of the Firestone Ride Rite air suspension systems use 1/4 inch tubing and 1/4 inch NPT fittings like the # F2012 that you referenced.

This kit includes 18' of red 1/4" air line, (2) 1/4" NPT (National Pipe Thread) elbow fittings, 1 union tee and 2 inflation valves for your Ride-Rite or Sport-Rite air helper spring system.

expert reply by: Jameson C

0

Answer 1

The standard air tubing diameter for Air Lift and Firestone air bag kits is 1/4 inch like the part #F2012 that you referenced. Firestone and Air Lift do not make a smaller diameter tubing at this time.

view full answer...

Answer 2

To replace the air lines on the Firestone Coil-Rite Air Helper Springs item #F4182 you can use the Firestone 1/4" Air Line Tubing item #F99ZR.

view full answer...

Answer 3

Hey Don! The Pacbrake Alpha HD #PB32ZV you were looking at does not have the internal jounce bumper. You would need the Pacbrake Alpha HD Pro Air Bag Suspension w/ Internal Jounce Bumpers #PB92ZV. The jounce bumper adds additional support when…

view full answer...

Answer 4

Good choice with the B&W Turnoverball #BWGNRK1108, Howard! It's definitely the way to go. With that installed on your 2007 Ford F-250 4 wheel drive you will want the Firestone Ride-Rite Air Helper Springs #F2400. These will absolutely work…

view full answer...

Answer 5

Hey Brandon - great question, and yes, the FX4 trucks have one extra check. Firestone wants you to measure the distance from the top of your rear axle to the bottom of the bump-stop bracket. If that measurement is 40 mm, 70 mm, or 80 mm, the wireless…

view full answer...

Answer 6

For your Air Spring Union Tee like #F3025-1 the only troubleshooting you can do is what you have already been doing. The Tee fittings simply use a compression so pushing into place is all that is required. The clean 90 degree cut is also all that is…

view full answer...

Answer 7

Hey Chris. The Single Function Air Spring Control Panel item #F2225 has almost everything you need to add the Firestone Air Tank - 1 Gallon item #F9244 to your existing setup. You'll need a couple of fittings like item #F3046-1 or item #F3031-1…

view full answer...

Answer 8

The Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle #F2410 is designed to flex from side to side when you use a single path compressor and T-valve. In talking with Firestone they have only every confirmed using the dual path…

view full answer...

Answer 9

The Air Lift Air Shock Controller Compressor, part #AL25804 includes the onboard compressor; dash mounted gauge panel; hardware and air lines. An air tank isn't included. Since the compressor is manually operated from the dash panel, a pressure…

view full answer...

Answer 10

It looks like you have the Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle #F2445 for your 2017 Toyota Tundra. The correct elbow connector is the Firestone Elbow Connector for 1/4" Tubing, 1/4 NPT - Male #F3031-1. Make…

view full answer...

Answer 11

First you will want to completely deflate the airbags. Then to remove the air line from a push to connect fitting like part #F3128-1 you first push the outer metal ring inward and then pull the air line out. You may also need to push in on the air…

view full answer...

Answer 12

I went out to the warehouse to confirm and the 1/4" air line in the Air Line Service Kit for Firestone Ride-Rite/Sport-Rite Air Helper Springs #F2012 will fit directly into the tee and elbow fittings that come with the kit. You do need to ensure…

view full answer...

Diameter of Tubing Used in the Firestone Ride Rite Air Suspension Kits

Product Page this Question was Asked From

Continue Researching