See what our Experts say about this Valterra RV Sewer Hose Fittings

• Looking for Replacement Seal for Valterra Rotating RV Sewer 3 Hub to Bayonet Adapter
  Hey Mike, we have a replacement seal for the Valterra 3 Hub to 3 Bayonet part # T1028 with the part # T201. Did you lose yours or did it get damaged?
  view full answer...
• Parts Needed To Add A 3" Bayonet Fitting To An RV Sewer System
  Hey Brad, I would not use a rubber boot to connect to the # T1027. It would likely leak and wouldn't be stable enough for you to fully connect it to a waste hose, which could end up causing quite a mess. Instead you could use the # 344632893, which has a 3" hub side to glue # A05-0303 onto the pipe that you already have and a threaded side to screw the # T1027 into. You could also just glue on the # T1028 if the pipe is already sticking out far enough for you to connect your waste hose.
  view full answer...
• 1-1/2 inch Gray Tank to 3 inch Bayonet Fitting Adapter Recommendation
  We have the LaSalle Bristol Eccentric Tank Reducer # 34466V153 which can slide over your 1-1/2 inch diameter gray pipe to give you a 3 inch pipe that you could then attach the 3 inch pipe to 3 inch bayonet adapter part # T1028 and you'd be set.
  view full answer...
• Fittings Needed To Go From 3" MPT Threaded Sewer Pipe To 3" Bayonet Fitting
  You'll first want to attach the LaSalle Bristol Clean Out Adapter for RV Sewer System # 344633703 to your current setup and then you can attach either the Valterra RV Sewer Termination Adapter # T1029-2 or the Valterra Rotating Adapter for Rigid RV Sewer Pipe # T1028 to the unthreaded side of the # 344633703 with some Valterra ABS Solvent Cement # A05-0303
  view full answer...
  
• Needing a Rotating Adapter for Rigid RV Sewer Pipe
  Yes, of course you can insert and glue the Valterra Rotating Adapter for Rigid RV Sewer Pipe, # T1027 if you choose to. If your objective is to have a permanent/semi-permanent arrangement of your RV to a sewer system, I suggest the Valterra Rotating Adapter for Rigid RV Sewer Pipe, # T1028. This adapter converts an RV waste valve to connect to 3" hub sewer pipe. The bayonet fitting rotates, making it easy to connect to the lug fitting on your RV's waste valve and the 3" hub slides over...
  view full answer...
  
• Solution To Go From A 1-1/2 Inch Hose Fitting To A 3 Inch Bayonet Fitting
  We have the LaSalle # 34466V153 which will slide on over your 1-1/2" pipe to give you 3" pipe. From here you can use # T1028 to give you the bayonet fitting you're needing. Use the solvent cement # 3447530889 to complete installation and prevent leaks.
  view full answer...
• Could Valterra Rotating Adapter for Rigid RV Sewer Pipe Fit Schedule 20 and 40 Sewer Pipe
  There is Schedule 20 and 40 sewer pipe that has an outer diameter of 3-1/2 inches like what the Valterra Rotating Adapter for Rigid RV Sewer Pipe # T1028 is designed to work with so yes it would fit if the size was correct.
  view full answer...
• Glue to Use to Connect RV Sewer Pipe
  When gluing together Valterra RV sewer pipes like the # T1028 you'd need to use an ABS solvent cement like the part # A05-0303.
  view full answer...
• Can A 3 Inch Pipe Be Attached to the Valterra Adapter for RV Sewer Hose Part # T1025VP
  The Valterra Adapter for RV Sewer Hose part # T1025VP has a bayonet fitting on one end and then a tapered fitting on the other end. There would be no way to attach a 3" pipe to the tapered fitting but what you could do is combine the Valterra Street DWV Fitting part # D50-2892 and the Valterra Rotating Adapter part # T1028 to provide a bayonet fitting on one end and then a hub fitting on the other which you would then slide a 3" pipe into. Please note, RV's use ABS pipe construction not...
  view full answer...
• Replacement Gasket for Valterra Bayonet Sewer Fitting
  For replacement gaskets for the bayonet side of the Valterra fitting # T1028 you'd want to use the part # CAM39834.
  view full answer...
• Recommended Bayonet Flange For Waste Valve
  For the bayonet fitting on your valve, you can use the Valterra Rotating Adapter for Rigid RV Sewer Pipe - 3" Hub to 3" Bayonet - Black Plastic # T1028, the Valterra Adapter for RV Sewer Hose - 3" Bayonet Fitting - Straight - Black # T1024VP, or the Valterra Hose Adapter w/ 3" Swivel Bayonet Fitting - Black # T1024-2VP. For the other side of that bayonet, you may be interested in the Valterra RV Sewer Lug Fitting with Flange - 3" # T1009, the Valterra RV Sewer Termination Adapter - 3"...
  view full answer...
• Valterra Rotating Adapter for Rigid RV Sewer Pipe to Permanently Connect to Septic Station
  You will need the Valterra Rotating Adapter for Rigid RV Sewer Pipe - 3" Hub to 3" Bayonet - Black Plastic item # T1028 and a 4" to 3" adapter that you can find at your local hardware store to permanently connect your camper to you septic station.
  view full answer...
• Flange and Gasket for Installing RV Toilet
  Though we do not carry either of those parts I can still help you out. What you are going to need - depending on how your hose threads - is either the RV Toilet Floor Flange # T05-0784, which has 3" diameter female pipe threads OR RV Toilet Floor Flange # T05-0782, which has 3" diameter male pipe threads. Additionally you will need the RV Toilet Floor Gasket with Hold Down Bolts # Q23653VP which is a universal design that works with the flange.
  view full answer...
• How to Connect an RV Waste Sewer Hose to a Portable Tote Tank with Threaded Fitting
  I think I'm following you. It sounds like your portable tote tank has a threaded fitting, but your sewer hose has a bayonet fitting like a typical sewer hose. If that is the case, then I have a solution for you, but we don't have a single adapter. Instead, you will want to use fitting # T1029-2 and fitting # 344633703 to make the adapter you need. The non-threaded end of part # 344633703, will fit into the end opposite of the 3 bayonet lugs on part # T1029-2. You will want to use ABS...
  view full answer...
• Does Valterra T1028 Rotating Rigid Pipe Adapter Leak
  Most likely the issue is related to the glue you used for your application. PVC and ABS require different glue types so you should verify that you used the correct glue for your application. If that's not the issue the problem is possibly the wrong size fitting.
  view full answer...
• Semi-Permanent RV Sewer Connections Made To Septic and Fresh Water Supply Needed - 75 Feet
  Your fresh water hose is an easy recommendation, I suggest the Camco RV drinking water hose, 5/8" diameter at 75' Long, # CAM22803. This is a reinforced PVC hose for drinking water made of FDA-approved materials and BPA-free. Because you state that you are new to RV living I will make the suggestion that you also use a water pressure regulator, I suggest the Camco RV Water Pressure Regulator, # CAM40055. Please see the attached video for a visual of product. Because inconsistent water...
  view full answer...
• Will LaSalle Bristol RV Sewer Termination Adapter Connect to 3" PVC Pipe
  The LaSalle Bristol RV Sewer Termination Adapter # 34466V293B3S is designed to slide into a larger hub like what you see on the end of # T1028 and secured using ABS Solvent Cement # 3447530889. The inner diameter on the hub should be about 3-1/2 inches. If this is what is on the PVC pipe that you mentioned then it will work great. I don't recommend connecting it directly to another 3 inch diameter PVC pipe though, as this might not allow for the best connection even when using a healthy...
  view full answer...
• Parts Needed To Make 1-1/2" Waste Valve With 3" Bayonet Outlet
  I do have a way for you to get what you want, but that's not something that's made. You'll need a few parts: Waste Valve # T1001 Adapter # T1041-1 Bayonet Adapter # T1028 ABS Glue # A05-0303 You mentioned PVC but your 1-1/2" Grey water pipe should be black ABS plastic per RVIA regulations and not PVC however. You'll connect the waste valve to hub end to your existing pipe, the adapter to the other end of the waste valve, and the bayonet adapter to that adapter.
  view full answer...
• Can the Valterra Rotating Sewer Adapter Be Temporarily Installed
  The Valterra Rotating Adapter for Rigid RV Sewer Pipe part # T1028 is designed to be welded to the end of a 3" ABS sewer pipe. However, if you don't want to permanently attach the sewer pipe to the hub fitting you could most likely just use a gasket maker like part # LT37467 to stop any leaks.
  view full answer...
• Fitting and Adapter for Waste Pump Sewer Pipe
  The Valterra Rotating Adapter for Rigid RV Sewer Pipe - 3" Hub to 3" Bayonet # T1028 is designed to fit onto a 3" waste valve with the bayonet fitting and the 3" hub will slide onto the sewer pipe so you can have your sewer pipe go between this adapter and the pump. There are other adapters, but they are all going to depend on the fittings you have. For example, the Clearview Adapter for RV Sewer Hose # T1026-1 is a clear and has a 45 degree angle, but uses 3" bayonet and lug fittings,...
  view full answer...
• 20 Foot Cleanout Hose With Adapters For RV
  I might have a solution for you, however, we do not have a 60' hose like requested. Instead, we have the EZ Flush Replacement RV Sewer Hose with 3" Bayonet Fitting # D04-0087 which is 15 mil thick, and is 20' long. With this hose, you'll need # 344633703 to connect to your RV's cleanout, and use # T1028 on the smooth end of # 344633703. This setup will allow you to connect # D04-0087 to your RV's cleanout. Additionally, you will need some solvent cement # A05-0303 to secure # 344633703...
  view full answer...

Do you have a question about this RV Sewer Hose Fitting?