Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub

See what our Experts say about this Valterra RV Sewer Hose Fittings

• Diameter of the Larger Side of the Valterra RV Sewer Hose Reducers T1041-1 and T1041-2
  If you check out the video link I attached you can see where our demo guy measures the larger side of the T10401-2 and it has an outer diameter of 3-1/2 inches and an inner diameter of 3 inches. Right at the 29 second mark you can see the ruler held up to the product so you know he isn't mistaken. That end is going to fit over a 3 inch sewer pipe like you mentioned.
  view full answer...
• 3 inch to 1-1/2 inch Reducer for RV Sewer Piping
  The adapter you need is the Valterra part # T1041-1 that you referenced as it fits your configuration needs. The 3 inch portion fits into the tank and then the 1-1/2 inch portion fits over the elbow fitting like you need. Rubber cement is basically not designed to be broken up though.
  view full answer...
  
• Gray Water Tank Reducer With 3.5" OD
  If I understand correctly, you need a reducer with an OD of 3.5". The 3" Spigot Valterra Eccentric Tank Reducer, # T1041-1 that you linked to is a 3.5" OD with a 3.0" ID measurement.
  view full answer...
• Do RV Sewer Pipes Have to be Cut Completely Off When Removed and Reinstalled
  What's interesting about the ABS fittings of RV sewer pipes is that they have to be completely cut off and can't be cleaned or removed. It has to be completely cut off and everything has to be new.
  view full answer...
• What Normally Seals RV Sewer Pipes
  When replacing RV sewer lines you have to cut them totally off since the ABS cement is a permanent plastic weld. Then when you go to make new connections you end up having to replace anything that can't be separated. Or you can use adapters to fit into or over the old pipes and use solvent to make the connection. For solvent we have the part # 3447530889.
  view full answer...
• Best Trailer Hitch for a 2020 Subaru Outback
  The best trailer hitch for a 2020 Subaru Outback is the EcoHitch Hidden Trailer Hitch Receiver part # EH34FR which is a direct bolt-on fit with no major modifications required for installation. The EcoHitch Hidden Trailer Hitch Receiver as the name suggests has a hidden design which means only the required cross tube will be shown therefore you won't take away from the overall look of the vehicle. Furthermore, the receiver tube is tucked under the rear bumper so you don't lose any ground...
  view full answer...
  
• Removal and Installation of Valterra Gray Water Tank Reducer
  In most cases the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub # T1041-1 is going to be attached to the gray water tank with an ABS solvent like # A05-0303, so it will need to be cut off in order to replace it.
  view full answer...
• What Bonding Agent Should Be Used To Attach RV Sewer Pipe Fittings
  Unfortunately just looking at a picture isn't going to be enough for me to identify what the manufacturer used to glue the 3" pipe reducer # T1041-1 to the other fitting, however I can tell you that you should use some ABS # A05-0303 when you're ready to hook up your new pipe reducer.
  view full answer...
  
• What Kind of Sealant is Used to Install Valterra Eccentric Tank Reducer # T1041-1
  To attach the Valterra Eccentric Tank Reducer # T1041-1 to the rest of the plumbing on the RV and prevent leaks use the Valterra ABS Solvent Cement # A05-0303. It was made for exactly this purpose!
  view full answer...
  
• Removing and Installing Valterra Eccentric Tank Reducer # T1041-1
  The Valterra Eccentric Tank Reducer, part # T1041-1, is installed with cement. When you reinstall the new one use # A05-0303. The cement is permanent so you're not going to be able to break it up. Instead you need to cut the pipes after removing the hose clamps. Then replace it with the new one and apply the new cement. The same cement can be used on other plumbing parts as well.
  view full answer...
  
• Changing A Waste Drain From 1-1/2 To 3
  What you can do is hook the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub Item # T1041-1 onto your 1-1/2" pipe using some Valterra ABS Solvent Cement - 1/4 Pint Item # A05-0303 and a hose clamp. Next you'll hook in the Valterra RV Sewer Termination Adapter - 3" Lug Fitting to 3" Spigot Item # T1029-1 using some # A05-0303 and a hose clamp. If your hose has the bayonet end or if you have no end on the hose you can just hook it in as well using a hose clamp.
  view full answer...
• Is There a Way to Use Double RV Waste Valves - Sewer Wye with Two 1-1/2 Pipes
  I do have an option for you but none of our sewer wye valves feature two 1-1/2" inlet pipes into a single 3" outlet. That said, you can still use something like the Double RV Waste Valves - Sewer Wye part # TR38 by just reducing the 3" hub down to a 1-1/2" hub with the Valterra Eccentric Tank Reducer part # T1041-1. This would give you a 1-1/2" spigot and 1-1/2" hub but that's the best we can do.
  view full answer...
• Parts Needed To Make 1-1/2" Waste Valve With 3" Bayonet Outlet
  I do have a way for you to get what you want, but that's not something that's made. You'll need a few parts: Waste Valve # T1001 Adapter # T1041-1 Bayonet Adapter # T1028 ABS Glue # A05-0303 You mentioned PVC but your 1-1/2" Grey water pipe should be black ABS plastic per RVIA regulations and not PVC however. You'll connect the waste valve to hub end to your existing pipe, the adapter to the other end of the waste valve, and the bayonet adapter to that adapter.
  view full answer...
• What is the Difference Between Valterra EZ Valve Electric Waste Valves # E85-8 and # E84-8
  The difference between the Valterra EZ Valve Electric Waste Valves # E85-8 and # E84-8 is the design of the center output tube. On # E85-8 it's a straight, regular hub. On # E84-8 the center tube has bayonet fittings. Based on your pictures you would need # E84-8. However, the input size of either hub is 3 inches so your smaller tubes would not fit without adapting to the tubing size you have up to a 3 inch mating tube to fit the E84-8. It looks like the smaller tubes are 1-1/2 inch (measure...
  view full answer...
  
• Fittings Needed To Expand 1-1/2" Sewer Pipe To 3" Pipe
  To widen your 1-1/2" pipe to 3" using the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub # T1041-1 you would first need the Valterra DWV Adapter for RV Sewer System - ABS Plastic - 1-1/2" Hub to FPT # D50-2922 to screw onto your current fitting. The # T1041-1 would then slide over the 1-1/2" hub fitting of the # D50-2922 allowing you to connect a 3" pipe to your sewer system. Between these two fittings you'll want to use some ABS Solvent Cement # A05-0303 to...
  view full answer...
  
• Is There a Valterra EZ Valve Double Electric Waste Valve for 3" and 1-1/2" Valves
  The Valterra EZ Valve Double Electric Waste Valves are only available in 3". If you have a 1/2" and 3" setup then you will need to upgrade to 3" in order to use one. I recommend part # E85-8 and then part # T1041-1. You'll also need part # A05-0303 to complete the swap along with some misc. pipe.
  view full answer...
• 3-1/2" Eccentric Tank Adapter With Installation Instructions
  The Valterra Eccentric Tank Reducer # T1041-1 is most likely what you're going to need, however it will be difficult to tell you what you need without knowing what you currently have. The Valterra Eccentric Tank Reducer # T1041-1 has a 3" spigot end that will install inside the neck of the waste water tank, and has a 1-1/2" hub end that you will slide your pipe into. You can use some gasket maker # LT37467 to secure the spigot end into the neck of the tank, and use a hose clamp # H03-0009...
  view full answer...
• Recommended Adapter To Use 3" Valterra EZ Valve Electric Waste Valve On 1-1/2" Gray Water Tank
  Absolutely! To install the Valterra EZ Valve Electric Waste Valve # E40A-8 on your gray water tank with 1-1/2" pipe you can simply use the Valterra Eccentric Tank Reducer 3" Spigot to 1-1/2" Hub # T1041-1 on each side of the waste valve to convert the 3" openings to 1-1/2". The Valterra EZ Valve # E40A-8 includes a gray water switch plate for you to use as well. You will also need Valterra ABS Solvent Cement # A05-0303 for a strong leak free connection.
  view full answer...
• How To Install Valterra Eccentric Tank Reducer
  The Valterra Eccentric Tank Reducer part # T1041-1 has a 3" spigot end which installs inside the neck on the waste water tank and then a 1-1/2" hub end which you would slide a pipe into. In order to secure the spigot end into the neck on the tank you will want to use some gasket maker part # LT37467 on the outside of the spigot fitting or on the inside of the water neck and then use a band clamp part # H03-0009 to clamp down on the waste water neck and hold the spigot fitting in place....
  view full answer...
• Installing Valterra Eccentric Tank Reducer and RV Waste Valve to Gray Water Tank
  When installing the Valterra Eccentric Tank Reducer # T1041-1 to your existing tank with a 3" opening you will just need to use some ABS solvent cement like # A05-0303 for the attachment. This is also what you will use to add the LaSalle Bristol Cable-Actuated RV Waste Valve # 34466N11AB48GMA to the fitting. You will want to coat the outside AND inside of each fitting with the solvent before connecting the components. What this does is actually cause a chemical reaction with the plastic...
  view full answer...
• Parts Needed For A 3" To 1.5" To 3/4" Black Tank To Grey Tank Conversion
  It sounds like you're going to need the Valterra Eccentric Tank Reducer # T1041-1 which will mount directly to your 3" spigot, while the 1-1/2" hub slides over the sewer pipe. Now you can connect to the Valterra Waste Valve for RV Gray Water Tank w/ Cap # T1001C, like you mention. From here, you can attach the Valterra Gray Water Drain Connector # T01-0094VP for the 3/4" hose connection, or you can use # T01-0091VP if you want a 90° angle 3/4" hose connection. We have various hoses...
  view full answer...
• Replacement Gray Water Tank Reducer Adapter from 3 Inch to 1-1/2 Inch
  It sounds like you are looking for the Valterra Eccentric Tank Reducer part # T1041-1 which installs in an RV gray water tank with with 3" diameter opening and then reduces this down to 1-1/2". The adapter will install inside the neck on the tank and then secured with gasket maker part # LT37467 and a band clamp part # H03-0009. In order to replace the waste valves you can then use the Double RV Waste Valves part # T80A depending on your setup. Please note, you'll also need the Valterra...
  view full answer...
• Upgrading To Electronically Controlled Waste Valves
  If you're wanting to have an electronically controlled valve for just the gray tank then you can use the Valterra EZ Valve Electric Waste Valve for RV Black Water Tank - 3" Hub to 3" Hub # E40B-8 along with a reducer # T1041-1 to make the connection between the valve and gray water pipe. There currently are no electronically controlled valves with a 1-1/2" opening so you'll have to use a black water tank valve to accomplish this. You could also use the Valterra EZ Valve Double Electric...
  view full answer...
• Adapter for 3 RV Gray Water Tank Opening to 1-1/2 Pipe and Waste Valve
  From what I can gather it sounds to me like you need the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub # T1041-1. The 3" Spigot mounts directly in the gray water tank outlet while the 1-1/2" Hub slides over sewer pipe. Then for a 1-1/2" diameter gray-water sewer pipe we have the LaSalle Bristol Cable-Actuated RV Waste Valve for Gray Water Tank. This is valve is available in with cables that are numerous lengths, which I'll list for you so you can choose the...
  view full answer...

Do you have a question about this RV Sewer Hose Fitting?