Front Receiver Hitch Specs:
Features:
Attach accessories to the front of your vehicle with this trailer hitch receiver. Perfect for winches, spare tire carriers and more. Hidden cross tube leaves only receiver visible. Aluminum and steel alloy construction is sturdy and eco-friendly.
Installation Notes:
No drilling required for installation
Front air dam will need to be temporarily removed for installation and will need some modification when replaced
Intercooler shroud will need to be trimmed
Hitch includes a front license plate bracket which installs in the hitch receiver opening when not in use
More Information >Front Receiver Hitch Specs:
Features:
Attach accessories to the front of your vehicle with this trailer hitch receiver. Perfect for winches, spare tire carriers and more. Hidden cross tube leaves only receiver visible. Aluminum and steel alloy construction is sturdy and eco-friendly.
Installation Notes:
No drilling required for installation
Front air dam will need to be temporarily removed for installation and will need some modification when replaced
Intercooler shroud will need to be trimmed
Hitch includes a front license plate bracket which installs in the hitch receiver opening when not in use
More Information >Videos
for Front Receiver Hitch
Help Articles
for Front Receiver Hitch
Expert Answers
for Front Receiver Hitch
From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a…
view full answer...I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that.…
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
view full answer...Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and…
view full answer...The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your…
view full answer...If your 2022 Chevrolet Tahoe does not have the factory tow package then the plug may not be there. If this is the case you would need to hardwire in a brake controller. If your Tahoe does have the tow package then the plug will be under the dash.…
view full answer...I do have an option for you but we have not yet gotten out hands on a 2019 Chevrolet Blazer therefore, have not had the chance to look for the brake controller wiring port either. I checked with both Tekonsha and Curt and it looks like they have…
view full answer...M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while…
view full answer...You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…
view full answer...The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So…
view full answer...