atv-utv tie downs - SpeedStrap

Hey Dave, thanks for reaching out! The Erickson Round D-Ring Tie-Down Anchor #EM59110 has a capacity of 1,200 lbs and is not going to be strong enough to cinch down your Polaris RZR securely. You need the CargoSmart Anti-Rattle D-Ring Tie-Down Anchor…

That’s a great question, Angela - and you’re definitely not alone there. The easiest way is to measure the clear deck width at the very back of the trailer, where the ramps will mount, making sure there aren’t side rails or stake pockets in the way.…

Hey Rodney, yes the etrailer ramp set part #e47XV will work for your Kubota L2025 as the ramps are rated for up to 6,000 lb and your tractor only weighs 2,800 lb. What kind of trailer do you have and where do you usually have to transport your…

Hey Bart! The Tie Down Side-Mount Spare Tire Mount #TD68FR can be used with a 3" tall trailer tongue. It actually comes with two different U-bolts so it will work with a 4" or a shorter 3" like yours. What kind of trailer do you have?

Hi Roger! I contacted Dexter with your axle information and you will need the #25580 inner bearing and #14125A outer bearing. If you want the races as well, you will need the #25520 and #14276 respectively. The seal will be the Double Lip -…

Hi John; personally I would use the etrailer E-Track Backing Plates #e96RR or #e66RR to secure the etrailer Horizontal E Track #e62VR. My next choice would be the bolts and washers, screws after that if you really want to go that route. It will be…

You can use either wheel nets or wheel straps with the Erickson E-Chock Wheel Chock for E-Track #EM09162 (this is a quantity of one strap but can be ordered in a pair at part #EM09162-2). I recommend the Erickson Adjustable Wheel Net with E-Track…

Hi Steve; the Air Lift WirelessONE Compressor System for Air Helper Springs #AL25980EZ and #AL25980 are both single path systems and come with a remote and Bluetooth functionality. The main difference is the mounting and the compressor. The…

They sure are Charlie and welcome back! The biggest inconvenience you're going to run into removing and reinstalling the Coil SumoSprings item #CSS-1125R are jacking up the rear end of your Subaru each time and removing the rear wheels. You will…

Hey Doug, I looked up your axle part number and was able to determine that it is a 5,200 lb axle with brakes and a 6 lug bolt pattern but I was not able to find the overall length of the axle from hub face to hub face as well as the spring seat to…

The Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs #RR5K are rated for 5,000 lbs break strength and will work just fine with your application. The 3/4 inch plywood floor is very strong and with the…

Hello David, thanks for reaching out. It is possible to switch your trailer over to a lunette ring/pintle hitch system. Basically you will need to replace your current A-frame coupler with a channel coupler like part #LR76VR. This will allow you to…

Hey Dave, thanks for reaching out! The Erickson Round D-Ring Tie-Down Anchor #EM59110 has a capacity of 1,200 lbs and is not going to be strong enough to cinch down your Polaris RZR securely. You need the CargoSmart Anti-Rattle D-Ring Tie-Down Anchor…

That’s a great question, Angela - and you’re definitely not alone there. The easiest way is to measure the clear deck width at the very back of the trailer, where the ramps will mount, making sure there aren’t side rails or stake pockets in the way.…

Hey Rodney, yes the etrailer ramp set part #e47XV will work for your Kubota L2025 as the ramps are rated for up to 6,000 lb and your tractor only weighs 2,800 lb. What kind of trailer do you have and where do you usually have to transport your…

Hey Bart! The Tie Down Side-Mount Spare Tire Mount #TD68FR can be used with a 3" tall trailer tongue. It actually comes with two different U-bolts so it will work with a 4" or a shorter 3" like yours. What kind of trailer do you have?

Hi Roger! I contacted Dexter with your axle information and you will need the #25580 inner bearing and #14125A outer bearing. If you want the races as well, you will need the #25520 and #14276 respectively. The seal will be the Double Lip -…

Hi John; personally I would use the etrailer E-Track Backing Plates #e96RR or #e66RR to secure the etrailer Horizontal E Track #e62VR. My next choice would be the bolts and washers, screws after that if you really want to go that route. It will be…

You can use either wheel nets or wheel straps with the Erickson E-Chock Wheel Chock for E-Track #EM09162 (this is a quantity of one strap but can be ordered in a pair at part #EM09162-2). I recommend the Erickson Adjustable Wheel Net with E-Track…

Hi Steve; the Air Lift WirelessONE Compressor System for Air Helper Springs #AL25980EZ and #AL25980 are both single path systems and come with a remote and Bluetooth functionality. The main difference is the mounting and the compressor. The…

They sure are Charlie and welcome back! The biggest inconvenience you're going to run into removing and reinstalling the Coil SumoSprings item #CSS-1125R are jacking up the rear end of your Subaru each time and removing the rear wheels. You will…

Hey Doug, I looked up your axle part number and was able to determine that it is a 5,200 lb axle with brakes and a 6 lug bolt pattern but I was not able to find the overall length of the axle from hub face to hub face as well as the spring seat to…

The Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs #RR5K are rated for 5,000 lbs break strength and will work just fine with your application. The 3/4 inch plywood floor is very strong and with the…

Hello David, thanks for reaching out. It is possible to switch your trailer over to a lunette ring/pintle hitch system. Basically you will need to replace your current A-frame coupler with a channel coupler like part #LR76VR. This will allow you to…