The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Hey John! Since you have the same number of teeth the Replacement 24 Tooth Pinion Spur Gear for Power Gear RV Slide Outs #LC86EX will likely work as a replacement. I would measure the outer diameter as well. If it matches the 1.417" measurement…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
The Fixed Dual Rack Repair Kit #LC84FR goes on the left side of the slide as you look at the slide out from the outside of the camper. So on the drivers side it will be the front of the slide. The Floating Dual Rack Repair Kit #LC26VR is going to be…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
Hey Kyle, yes the Flair-It High Pressure Hose #FL37FR does fit on the 1/2 barb fitting of the Flair-It PEXLock Female Elbow Fitting #FL44ZR that you also referenced.
Hey Henry! I would be happy to help you get your 2026 Jeep Wrangler ready for flat towing. You will need the tow bar, base plate, safety cables, wiring, and a supplemental brake system. I recommend the following: -Blue Ox Base Plate Kit - Removable…
Thanks for the good experience. Minus the one part that got shipped later due to availability, the products arrived ahead of the anticipated date. Real to life 'Live Help' is great, hope you can manage to keep it up. If I have further needs, will contact you guys again.
Andrew
Minneapolis, MN
RV Slide Out Parts caps and covers for radius corner
Tidy up and protect your RV slide-out with caps and covers shaped for a radius corner. These parts finish off curved edges neatly and can replace worn pieces on spots like a bottom front or top rear corner. Measure your corner and mounting hole spacing so everything lines up for a clean, secure fit.
Dry-fit the cover first to confirm the Radius Corner shape and edge lengths match. Mark and verify the mounting holes center to center before fastening. For top rear or bottom front placements, hold the cover in its final orientation to ensure the curve and edges track the corner correctly.
Yes, they can fit a bottom front corner. One was used on a bottom front corner of a trailer and fit. Verify the Radius Corner matches your profile and that the hole spacing lines up. If you're mirroring a top rear style to a bottom front spot, double-check orientation before drilling or fastening.
Match the overall size and the Radius Corner shape on your RV. Measure both edges of your corner the same way you'll measure the Caps and Covers, and compare the mounting hole spacing center to center. Check the corner location—top rear or bottom front—so the orientation lines up.
Pick Caps and Covers measured the same way you measured—edge to edge on both sides. Compare your size to the listed dimensions and check the center-to-center mounting hole spacing. If it isn't an exact match, evaluate how close it is and whether the holes and Radius Corner will still align with your corner.
Filters
