The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hi Ron, thanks for reaching out. I completely understand why you're checking that measurement before ordering since if the fins don't reach the slide wall, the seal won't do the job you're expecting. The Rubber Bulb Seal with Fins for…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey Martin, The only difference I'm seeing between the Replacement Motor #TUS24FR and the Replacement Motor #LC125802 is that the TUS24FR has a 9000 RPM rating while the LC125802 has a 440 RPM rating while under load, which jumps up to 500 RPM…
To get right seal you'll need to remove a portion of the seal to get the side profile of your current seal. There are multiple types of applications for slide-out seals; Glue On, Peel-N-Stick, Press In, Push On, and Slide-On. There are multiple…
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Hey Donna, you would have to replace the entire setup as there was a refrigerant law change in January of 2025 that forced the complete systems to have to be redesigned and because of that nothing is currently backwards compatible. So what I would…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
Quick processing, and delivery. reasonably priced very satisfied
Bernie
Krakow, WI
RV Slide Out Parts caps and covers for radius corner
Tidy up and protect your RV slide-out with caps and covers shaped for a radius corner. These parts finish off curved edges neatly and can replace worn pieces on spots like a bottom front or top rear corner. Measure your corner and mounting hole spacing so everything lines up for a clean, secure fit.
Dry-fit the cover first to confirm the Radius Corner shape and edge lengths match. Mark and verify the mounting holes center to center before fastening. For top rear or bottom front placements, hold the cover in its final orientation to ensure the curve and edges track the corner correctly.
Yes, they can fit a bottom front corner. One was used on a bottom front corner of a trailer and fit. Verify the Radius Corner matches your profile and that the hole spacing lines up. If you're mirroring a top rear style to a bottom front spot, double-check orientation before drilling or fastening.
Match the overall size and the Radius Corner shape on your RV. Measure both edges of your corner the same way you'll measure the Caps and Covers, and compare the mounting hole spacing center to center. Check the corner location—top rear or bottom front—so the orientation lines up.
Pick Caps and Covers measured the same way you measured—edge to edge on both sides. Compare your size to the listed dimensions and check the center-to-center mounting hole spacing. If it isn't an exact match, evaluate how close it is and whether the holes and Radius Corner will still align with your corner.
Filters
